Product Disposal; Ce Declaration Of Conformity - Nice Shel50Kit Instructions Et Avertissements Pour L'installation Et L'utilisation

and the declaration of conformity compiled by the installer (see section
TECHNICAL DOCUMENTATION).
2 Affix a dataplate on the door, specifying at least the following data: type of
automation, name and address of manufacturer (responsible for commis-
sioning), serial number, year of construction and CE mark.
3 Prepare and provide the owner with the declaration of conformity; the "CE
Declaration of conformity" in the section TECHNICAL DOCUMENTATION
must be compiled for this purpose.
4 Prepare and provide the owner with the form "Operation manual" in the
section TECHNICAL DOCUMENTATION .
5 Prepare and provide the owner with the form "Maintenance schedule" in
the section TECHNICAL DOCUMENTATION, containing all maintenance
instructions for all devices in the automation .
6 Before commissioning the automation, ensure that the owner is adequately
informed of all associated risks and hazards.
7 Permanently affix a label or plate on the door with the image shown in fig. 47
(minimum height 60 mm) bearing the text "CAUTION: RISK OF CRUSHING".
PERIODIC MAINTENANCE OPERATIONS
In general, this product does not require special maintenance; however, regular
checks over time will ensure system efficiency and correct operation of the
safety systems installed.
Therefore to ensure correct maintenance, refer to the chapter "Maintenance
Schedule" in the section "TECHNICAL DOCUMENTATION" at the end of the
manual.
Note: The contents of this declaration correspond to those of the last revision available of the official document, deposited at the registered offices of Nice S.p.a., before printing
of this manual. The text herein has been re-edited for editorial purposes.
Number: 290/SHEL
The undersigned Lauro Buoro, managing director, declares under his sole responsibility that the following product:
Manufacturer's name: NICE s.p.a.
Address: Via Pezza Alta 13, Z.I. Rustignè, 31046 Oderzo (TV) Italy.
Type: Electromechanical gearmotor with built-in control unit for sectional doors
Models: SHEL50, SHEL75
Accessory: Radio control series FLO, FLOR, Smilo
Complies with the requirements of the EC directive:
• 98/37/EC (89/392/EEC amended); DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 22 June 1998 regarding the approxima-
tion of member state legislation related to machinery
As envisaged in the directive 98/37/EC, start-up of the product specified above is not admitted unless the machine, in which the product is incorporated,
has been identified and declared as conforming to directive 98/37/EC.
The product also complies with the essential requirements stated in article 3 of the following EC directive, for the intended use of products:
• 1999/5/EC; DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 9 March 1999 regarding radio equipment and telecommuni-
cations terminal equipment and the mutual recognition of their conformity.
According to the following harmonised standards:
Health protection EN 50371:2002; Electric safety: EN 60950-1:2006; Electromagnetic compatibility: EN 301 489-1V1.8.1:2008;
EN 301 489-3V1.4.1:2002; Radio spectrum: EN 300220-2V2.1.2:2007
The product also conforms with the requirements of the following EC directives:
• 2006/95/EEC (ex directive 73/23/EC) DIRECTIVE 2006/95/EEC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 12 December 2006 regarding the
approximation of member state legislation related to electrical material destined for use within specific voltage limits
According to the following harmonised standard: EN 60335-1:1994+A11:1995+A1:1996+A12:1996+A13:1998
+A14:1998+A15:2000+A2:2000+A16:2001
• 2004/108/EEC (ex directive 89/336/EEC) DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of 15 December 2004 regarding
the approximation of member state legislation related to electromagnetic compatibility, repealing directive 89/336/EEC
According to the following harmonised standards: EN 61000-6-2:2005; EN 61000-6-3:2001+A11:2004
It also complies, within the constraints of applicable parts, with the following standards:
EN 60335-1:2002+A1:2004+A11:2004+A12:2006+ A2:2006, EN 60335-2-103:2003, EN 13241-1:2003; EN 12453:2002; EN 12445:2002;
EN 12978:2003
Oderzo, 27 September 2008

CE DECLARATION OF CONFORMITY

Revision: 1

PRODUCT DISPOSAL

This product is an integral part of the automation and therefore must be
disposed together with the latter.
As in installation, also at the end of product lifetime, the disassembly and scrap-
ping operations must be performed by qualified personnel.
This product comprises various types of materials: some may be recycled oth-
ers must be disposed of. Seek information on the recycling and disposal sys-
tems envisaged by the local regulations in your area for this product category.
Caution! – some parts of the product may contain pollutant or hazardous sub-
stances which, if disposed of into the environment, may cause serious damage
to the environment or physical health.
As indicated by the symbol alongside, disposal of this prod-
uct in domestic waste is strictly prohibited. Separate the
waste into categories for disposal, according to the meth-
ods envisaged by current legislation in your area, or return
the product to the retailer when purchasing a new version.
Caution! – Local legislation may envisage serious fines in
the event of abusive disposal of this product.
Lauro Buoro (Managing director)
English – 9