Additional Certifications; Specifications - 3M Speedglas G5-01 Directives D'utilisation

Additional Certifications

1. This product meets the requirements of certain industrial eyewear standards. It does not provide complete head, eye, and face protection
from significant impact and penetration and are not a substitute for good safety practices and engineering controls. Misuse may result in
serious bodily injury or death. For correct use, consult your supervisor and User Instructions or contact 3M Technical Service in the U.S.A.
at 1-800-243-4630. In Canada, call Technical Service at 1-800-267-4414.
2. When exposed to eye and face hazards, wear additional eye and/or face protectors appropriate to the hazard. ANSI Z87.1-2015 – Occupational
and Educational Eye and Face Protection, incorporated by reference in the OSHA Eye and Face Standard 29 CFR 1910.133, suggests safety
spectacles or goggles should be worn in conjunction with loose fitting respirators if the visor can be raised from the normal position during use.
Failure to do so may result in serious bodily injury or death.
When assembled according to these User Instructions, this welding helmet meets the high impact requirements of the ANSI Z87.1-2015 – Occupational
and Educational Eye and Face Protection standard for eye and face protection devices.
Occupational use of this product for eye and face and/or head protection must be in compliance with applicable health and safety standards. In the
US, employers must comply with the OSHA personal protective equipment (PPE) standard (29 CFR 1910.132) and, as applicable, the eye and face
standard (29 CFR 1910.133). In Canada, consult the applicable standard(s) for your jurisdiction.

SPECIFICATIONS

3M™ Speedglas™ Heavy-Duty W
NOTE: The
and 3M™ Speedglas™ Welding Auto-Darkening Filters ADF G5-01 and ADF G5-01VC
Technical Data
Approximate Viewing Area
Approximate ADF Battery Life
(1 x CR-2450)
Solar Assist
Welding Helmet Weight (w/headband and ADF)
Dark Shades
Special Modes
Light State
Switching Speed
Sensitivity Modes
TIG Rating
Number of Sensors
Delay (Recovery)
Welding Helmet & ADF Operating Temp Range
Standards Compliance
Other
ADF Warranty
Welding Helmet Warranty
Welding Helmet Headgear Suspension
Head sizes
Welding Helmet, ADF & Task Light Material
Task Light Reflector
Welding Helmet Headband
Visor & Protection Plates
Flame Resistant Fabric
Airflow Range
Noise Level
Storage Temperature Range*
* -4°F to 131°F (-20°C to 55°C) suggested storage temperature range if product will be stored for an extended period of time before first use.
elding Helmet G5-01 contains no component made from natural rubber latex.
Table 2. Specifications for 3M™ Speedglas™ Heavy-Duty Welding Helmet G5-01
Table 3. Additional Technical Information
6 to 15 cfm (170 to 425 lpm)
Less than 80 dB(A) (excluding external noise)
-22°F to 140°F (-30°C to 60°C)*
W WARNING
ADF G5-01
2.9 x 4.3 in.
(73 x 109 mm)
1,500 hours
No
34.4 oz. (975g)
5, 8, 9, 10, 11, 12, 13
Tack Mode
< 0.1 milliseconds at 73F (23C)
Adjustable 50 - 1300 milliseconds (approx.)
23°F to 131°F (-5°C to 55°C)
Meets performance criteria of CSA Z94.3-2015 (tested at non-CSA independent lab)
Acrylonitrile butadiene styrene (ABS)
Polyaramid (PA), Polypropylene (PP), Polyethylene (PE)
70% FR Cotton, 30% Polyaramid (PA)
4
ADF G5-01VC
2.9 x 4.3 in.
(73 x 109 mm)
1,500 hours
35.3 oz. (1000g)
5, 8, 9, 10, 11, 12, 13, 14
Variable Color Mode
Shade 3
5 levels
> 1 Amp
4
ANSI Z87.1-2015
3 Years
90 Days
1 Year
6 3/8 to 8 (50-64 cm)
Polyphthalamide (PPA)
Polycarbonate (PC)
No