Pump Oil Maintenance - Briggs & Stratton BPW3200 Manuel D'utilisation

NOTICE Improper treatment of pressure washer could damage it and shorten its life.
• DO NOT insert any objects through cooling slots.
• Use a soft bristle brush to loosen caked on dirt, oil, etc.
• Use a vacuum cleaner to pick up loose dirt and debris.
check and clean inlet screen
Examine the screen on the pump's water inlet. Clean it if the screen is clogged or
replace it if screen is damaged.
check High Pressure Hose
The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the
hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover,
damage or movement of couplings. If any of these conditions exist, replace the hose
immediately.
warning The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST equal or exceed maximum pressure rating of unit.
check detergent siphoning tube
Examine the filter on the detergent tube and clean if clogged. The tube should fit tightly
on the barbed fitting. Examine the tube for leaks or tears. Replace the filter or tube if
either is damaged.
detergent siphoning check Ball
Occasionally check ball in detergent siphoning system may become stuck from
storage, dried soap, or minerals in water. The check ball can be freed by performing
the following:
NOTICE Before performing this procedure, be sure you are wearing safety goggles as
described below.
warning Risk of eye injury.
Spray could splash back or propel objects resulting in serious injury.
• Always wear indirect vented (chemical splash) safety goggles marked to comply
with ANSI Z87.1 when using or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition goggles for indirect vented
safety goggles.
1. Shut off engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction, press red button and squeeze
spray gun trigger to release retained high water pressure.
warning The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Keep high pressure hose connected to pump and spray gun while system is
pressurized.
• ALWAYS point spray gun in safe direction, press red button and squeeze spray
gun trigger to release high pressure, every time you stop engine.
3. Remove detergent siphoning hose from barbed fitting on pump.
4. Using a firm, blunt object 7/64" (2 mm) in diameter or smaller, by at least 1"
(2.5 cm) long, such as an Allen wrench, slowly insert the object into the barbed
fitting until you meet resistance. This resistance is the check ball.
5. Slowly push down until you feel the ball move slightly, push no more than 1/8"
(3 mm). Slight pressure may be required to free the ball.
6. Repeat steps 4 and 5 if necessary.
7. Reinstall detergent siphoning hose onto barb fitting.
8. Treat with PumpSaver as described in Protecting the Pump during storage to
prevent reoccurrence.
check spray gun
Examine the hose connection to the spray gun and make sure it is secure. Test the
trigger by pressing the red button and making sure the trigger "springs back" into
place when you release it. You should not be able to press the trigger without pressing
the red button. Replace spray gun immediately if it fails any of these tests.
20 21
Figure
nozzle Maintenance
A pulsing sensation felt while squeezing the spray gun trigger may be caused by
excessive pump pressure. The principal cause of excessive pump pressure is a spray
tip clogged or restricted with foreign materials, such as dirt, etc. To correct the
problem, immediately clean the spray tip following these instructions:
1. Shut off engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction, press red button and squeeze
spray gun trigger to release retained high water pressure.
warning The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which could result in serious injury.
• Keep high pressure hose connected to pump and spray gun while system is
pressurized.
• ALWAYS point spray gun in safe direction, press red button and squeeze spray
gun trigger to release high pressure, every time you stop engine.
3. Remove spray tip from end of nozzle extension.
4. Use a small paper clip to free any foreign material clogging or restricting spray
tip (20).
5. Remove nozzle extension from spray gun.
6. Using a garden hose, remove additional debris by back flushing water through
nozzle extension (21). Back flush between 30 to 60 seconds.
7. Reinstall spray tip into nozzle extension.
8. Reconnect nozzle extension to spray gun.
9. Make sure garden hose is connected to water inlet. Check that high pressure
hose is connected to spray gun and pump. Turn on water.
10. Start engine following instructions How to Start Your Pressure Washer.
11. Test pressure washer by operating with each quick connect spray tip.
o-ring Maintenance
Through the normal operation of your pressure washer, o–rings are used to keep
the connections of the hoses and spray gun tight and leak–free. These o-rings may
become worn or damaged.
An O–Ring Maintenance Kit is provided with your pressure washer which includes
replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet
provided in the kit to service your unit's o-rings. Note that you will not use all of the
parts in the kit.
To remove a worn or damaged o–ring, use a small flathead screwdriver to get
underneath the o-ring and pry it off.
warning The high pressure stream of water that this equipment produces
could cut through skin and its underlying tissues, resulting in serious
injury and possible amputation.
• NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.
Pump oil Maintenance Figure
changing Pump oil
Change oil after first 50 hours of operation and then every 200 hours or 3 months,
whichever occurs first.
NOTICE When changing pump oil, use only high quality SAE 30 weight oil. Use no
special additives.
change pump oil as follows:
1. Clean area around brass oil drain plug at bottom of pump.
2. Remove oil drain plug. Drain oil completely into an approved container.
3. When oil has completely drained, install oil drain plug and tighten firmly.
4. Clean area around pump oil dipstick (a). Remove dipstick and fill pump with
recommended oil (approximately 14 fl. oz. (0.41 l)) to "Full" mark on dipstick.
5. Install pump oil dipstick.
6. Wipe up any spilled oil.
22
11