Publicité
Les langues disponibles
Les langues disponibles
Machine description (pict. 1-4)
1.
milling head
2.
cross-table
3.
machine post
4.
working spindle
5.
shift bar
6.
revolution selection switch
7.
control wheel for fine feed
8.
Emergency stop switch
9.
chuck with ring gear
10.
manual handle for cross slide
11.
manual handle for front carriage
12.
depth stop
13.
fastening nut for angle adjusting
14.
turning cross
15.
spindle guard
16.
guard against chips
Delivery range
1.
Mini drill and mill GBF 550
2.
chuck key
3.
hook key
4.
fastening pin
5.
tool box
6.
operating manual
Warranty
A warranty period of 12 months applies to commercial use
and 24 months apply to private use and commences on the
day of purchase of the device.
Warranty applies exclusively to failures due to defective
material or workmanship. An original sale slip with
indication of date of sale must be presented in case of
claiming for the warranty rights.
Warranty does not cover unprofessional use such as device
overload, violent use, damage caused by third party or
foreign materials, failure to comply with operations and
assembly manual, and normal wear and tear.
Technical data
Voltage/oscillation :
Coverage type (Motor):
Protection grade:
max. output:
max. drilling diameter:
straight milling:
shank milling:
morse taper in the spindle
folding machine head:
max. spindle-table distance:
overlapping:
spindle revolution – grade1/grade2:
table size:
noise level:
weight:
dimensions L x W x H (in mm):
EAN: 40 15671 48140 5
Ord. no.: 48140
*Operating schedule S3 (periodic duty)
Machine can be put to work with stated output for certain
period of time (relative switch period in % of working cycle).
Then it has to be on hold (break) to avoid overheating.
Working cycle consists of loading period and break period.
During the on hold position between the working cycles, the
machine will not cool down to surrounding temperature. The
working cycle is set to 10 min., if not stated otherwise.
230 V~50 Hz
IP 20
I
350 W (P1 S3 50%)*
13 mm
30 mm
16 mm
MK 3
-45°/+45°
220 mm
167 mm
-1
-1
0-1100 min
/0-2500 min
390 mm x 92 mm
L
82 dB
WA
49,2 kg
520 x 510 x 760
13
General safety instructions
Read the manual carefully before first use. If any doubts about
installation or operation occur, please contact the manufacturer
(Service department).
PLEASE OBSERVE FOLLOWING SAFETY INSTRUCTIONS
TO ENSURE HIGH LEVEL OF SAFETY:
Warning: Operate with RCD only (residual current
device)!
WARNING!
•
Keep your workplace clean and tidy.
Messy workplace or table increases the risk of accident
and injury.
•
Pay attention to your working environment. Electric
devices and milling tools shall not be used in damp or
humid environment. Secure proper lightning. Do not
expose the electric devices to rain or humid air. Do not
turn on the electric devices in environment with flammable
fluids and gases.
•
Do not let unauthorized persons to come close to the
machine. Keep observers and visitors, especially children
and older people, away from your workplace.
•
Store your tools safely.
Tools you are not using must be stored on dry, if possible
elevated place or lock them up to restrict the access to
other persons.
•
Use always job specific tools. Never use e.g. small tools
or accessories for job which requires big tools. Use only
tool designed for specific job. Do not overload the
machine.
•
Watch out for power cord. Do not pull the cord. When
disconnecting the cord pull the plug. Keep the cord away
from heat, oil and sharp edges.
•
Avoid accidental start up. Always ensure that the
starting switch is in off position before plugging the cord in
the socket.
•
Use special extension cables while working outdoors.
While working outdoors you will need special extension
cables bearing corresponding marking.
•
Keep your attention. Always pay attention to what you
are doing. Use common sense. Do not use electric devices
when tired.
•
Watch out for damaged parts. Check the machine before
use. Are there any parts damaged? In case of minor
damage consider if the tool will work fine and safely.
•
Avoid electric shocks.
Avoid any body contact with earthed objects, such as
water piping, heaters, cookers and refrigerators.
•
Use approved parts only. Use only identical spare parts
for maintenance and repairs. Contact the authorized
service department.
•
Warning! Using the accessories and attachments not
recommended in this operating manual can be dangerous
to people and objects.
•
Do not lean out of your working place.
Avoid abnormal body positions. Keep your stability and
balance.
•
Remove all tool wrenches etc. Before turning on make
sure that all wrenches and other adjusting tools are
removed.
Machine specific safety instructions
•
Always wear personal protective equipment when
operating the machine.
•
To avoid eye injury always wear eye protection.
•
If long haired, wear hair net or suitable working hat.
•
Wear skin tight working clothes. Rotating parts could catch
the sleeves etc.
•
Never take the metal chips out by bare hands.
Publicité
