Unpacking And Assembly - ST F 72 FL Manuel D'utilisation

Masquer les pouces Voir aussi pour F 72 FL:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

33. Danger! Ejected objects: Never use 
the machine without having fitted the exit 
guard!
34. Danger! Ejected objects: Keep bystand-
ers away.
35. Danger! Machine rollover: Do not use this 
machine on slopes greater then 10°.
36. Danger! Dismemberment: Make sure that 
children stay clear of the machine all the 
time when engine is running.
37. Danger of cutting yourself. Cutting 
means in motion. Do not put hands or feet 
near or under the opening of the cutting 
means housing.
38. Warning! Keep away from hot surfaces.
39. Avoid injuries caused by moving belts:
Never start up the machine without the 
safety guards in place. Keep a safe dis-
tance between you and the belts.
NOTE The images corresponding to the texts
in chapters 3 et seq., can be found on pages iii et
seq. of this manual.

3. UNPACKING AND ASSEMBLY

For storage and transport purposes, some com-
ponents of the machine are not installed in the 
factory and have to be assembled after unpack-
ing. Follow the instructions below.
IMPORTANT The machine is supplied without
engine oil or fuel. Before starting up the engine,
fill with oil and fuel following the instructions given
in the engine manual.
WARNING!
Unpacking and completing
the assembly should be done on a flat and
stable surface, with enough space for mov-
ing the machine and its packaging, always
making use of suitable equipment.
3.1 UNPACKING
When unpacking the machine, take care to 
gather all individual parts and fittings, and do 
not damage the cutting-means assembly when 
taking the machine off the pallet.
The standard packaging contains:
–    t he machine;
–    t he steering wheel;
–    t he seat;
–    c utting means engagement control lever ex-
tension;
–  dashboard cover;
–  steering wheel column caster;
–    t he grass catcher components;
–    t he syringe used to suction the engine oil.
–      an envelope containing the instructions 
manual, documents and screw supply also 
containing 2 sets of keys and a spare 10 Am-
pere fuse (6.3 A with Honda motor).
NOTE To avoid damaging the cutting-means
assembly when getting the machine down from
the pallet, take it to the maximum height and be
very careful.
Hydrostatic transmission:
–    T o make it easier to get the machine off 
the pallet and to move it, the rear drive dis-
engage lever should be put in position «B» 
(see 4.21.3).
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
3.2 ASSEMBLY AND CONNECTING
THE BATTERY (Fig. 3.1)
Remove the front cover (1) lifting it from the 
lower part.
Connect the three red cables (3) to the positive 
terminal (+) and the three black cables (4) to the 
negative terminal (–) using the screws supplied. 
Follow the instructions given.
Reassemble the front cover (1) inserting the two 
tabs (2) in their housing correctly and pressing 
the lower part till it clicks.
Charge the battery following the battery manu-
facturer's instructions.
IMPORTANT To prevent the safety device in
the electronic circuit board from cutting in, never
start the engine until the battery is fully charged!
WARNING!
turer's instructions regarding safe handling
and disposal.
3.3 FITTING THE DASHBOARD
AND STEERING WHEEL (Fig. 3.2)
Put the machine on a flat surface and straighten 
the front wheels.
Fit the caster (3) on the steering column (2), 
making sure the plug (1) is correctly fitted into 
the caster seat.
Fit the dashboard cover (5) making sure all 
fastenings click into their respective housings 
correctly.
Fit the steering wheel (6) onto the caster (3) with 
all the spokes directed towards the seat.
Fit the steering wheel fastening it with the 
screws (7) supplied, in the indicated order.
Fit the steering wheel cover (8) clicking the three 
fasteners into place. 
6
Follow the battery manufac-

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

F 72 fl hydro

Table des Matières