Items Supplied - Evolution RAGE 5 Traduction Du Manuel D'origine

SAFETY PRECAUTIONS FOR TABLE SAWS
a) Do not use saw blades which are
damaged or deformed.
b) Replace the table insert/access plate if
worn.
c) Use only blades as recommended in this
manual, which conform to EN 847-1. When
changing a saw blade ensure that the width of the
groove (kerf) cut by the blade is slightly greater
than the thickness of the riving knife. Also the
thickness of the blade body must not be greater
than the thickness of the riving knife.
d) Take care that the selection of the saw
blade is suitable for the material to be cut.
e) Wear suitable personal protective
equipment when necessary. This could include:
Hearing protection to reduce the risk of
induced hearing loss.
Respiratory protection to reduce the risk of
inhalation of harmful dust.
Wearing gloves when handling saw blades or
rough material.
f) Saw blades should be carried in a holder
whenever practicable.
g) Never perform any operation freehand.
This means using only your hands to
support or guide the workpiece. Always use
either the fence or mitre gauge to position and
guide the work.
WARNING:
Freehand cutting is a major
cause of accidents.
h) Never attempt to free a stalled blade
without first turning the saw off. Turn the
power off immediately to prevent damage
to the motor.
i) Provide adequate support for long or
wide workpieces.
j) Avoid awkward operations and hand
positions where a slip could cause your
hand to move into the blade.
k) Do not operate the appliance with a
damaged cord or plug. If the supply cord
is damaged, it must be replaced by the
8
www.evolutionpowertools.com
manufacturer or its service agent or
a similarly qualified person in order
to avoid a hazard.
ADDITIONAL SPECIFIC SAFETY
RULES FOR TABLE SAWS
WARNING:
Before using your table saw it is
important that you read and understand these
safety rules. Failure to follow these rules could result
in serious injury to the operator or damage to the
table saw.
a) Always use the blade guard. The blade
guard must always be used in every operation.
b) Hold the work firmly. Against the mitre
gauge or rip fence.
c) Always use a push stick. Especially when
rip cutting narrow stock.
d) Keep guards in place and in working
order. Always ensure that the riving knife is
fitted and correctly adjusted. Inspect the riving
knife regularly and replace it if it is worn. Use
only a genuine Evolution riving knife as this is a
dedicated component for this machine.
e) Remove adjusting keys and wrenches.
Form the habit of checking to see that keys
and adjusting wrenches are removed from the
machine before turning it on.
f) Do not use in dangerous environment.
Do not use power tools in damp or wet
locations, or expose them to rain. Keep work
area well lit. Keep the area well ventilated.
g) Keep children away. All children and
visitors should be kept at a safe distance from
the work area.
h) Do not use High Speed Steel (HSS)
blades. Ensure that the correct blade is selected
for the material being cut.
i) The push stick or push block should
always be stored with the machine when
not in use.
j) Connect the saw to a dust collection
device when sawing wood. The operator
should be informed of the factors that influence
exposure to dust e.g. type of material being cut
www.evolutionpowertools.com
and the importance of local extraction (capture
or source) and the proper adjustment hoods/
baffles/chutes.
k) Use proper extension cord. Make sure any
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your machine will
draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and
possible overheating.
l) Always use safety glasses. Also use a face
or dust mask if the cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
m) Maintain tools with care. Keep tools sharp
and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
n) Disconnect from the power supply before
servicing, cleaning or and when changing
accessories, such as blades.
o) Use recommended accessories. Only use
genuine Evolution accessories.
p) Check for damaged parts. Before further
use of the tool, a guard or other part that
is damaged should be carefully checked to
determine that it will operate properly and
perform its intended function - check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or replaced.
q) Keep hands out of the path of the saw
blade.
r) Never reach around the saw blade.
s) Turn off machine and wait for saw
blade to stop before making any fence
adjustments.
t) Never pull or carry the tool by the power
cord. Carrying or pulling the tool by the power
cord could cause damage to the insulation or
the wire connections resulting in the possibility
of electric shock or fire.
u) When transporting the machine use a
transportation device.
9
Never use the guards for handling or
transportation.
v) During transportation the upper part of
the saw blade must be lowered fully and
covered by the guard.
w) All operators using this machine must
read the instructions and familiarize
themselves with the machines workings.
x) Never leave the saw running and
unattended. Do not leave the saw until the
saw has been switched OFF, and the blade
has come to a complete halt.

ITEMS SUPPLIED

Description Quantity
Blade Changing Tools 3
Mitre Gauge 1
Assembly
Hold Down Clamp 1
Assembly
Adjustable Rip Fence 2
Push Stick 1
Blade Guard 1
Instruction Manual 1
TCT Multi Purpose 1
Blade (Fitted)
Riving Knife 1
EN
DE
ES
FR
IT
NL