Preparing A New Sprayer; Operator Controls - WAGNER LineCoat SP Serie Manuel D'utilisateur

Assembling the Sulky (LineCoat 880 SP)
The hitch coupler needs to be bolted to the sulky cart before
using the LineCoat 880 SP for the first time. The hitch coupler
along with the necessary screws, flat washers, and lock nuts are
included with the unit literature kit.
1. Slide the hitch coupler onto the tongue of the sulky cart.
2. Align the holes on the hitch coupler with the holes on the
sulky cart, and insert two hex screws with flat washers into
the holes.
3. Place a flat washer and lock nut onto each of the hex
screws. Tighten securely with a wrench.
Sulky Cart
Hex Screw
Hitch
Coupler
4. Make sure the hitch lever on the hitch coupler is in the
unlocked position.
5. Slip the hitch coupler over the hitch ball on the back of the
line striper cart. Push down on the hitch lever to lock the
sulky cart to the line striper cart.
Hitch Ball
Hitch Coupler

Preparing a New Sprayer

If this sprayer is new, it is shipped with test fluid in the fluid
section to prevent corrosion during shipment and storage. This
fluid must be thoroughly cleaned out of the system with mineral
spirits before you begin spraying.
Always keep the trigger lock on the spray gun in
the locked position while preparing the system.
Attention
1. Place the siphon hose into a container of mineral spirits.
2. Place the bleed hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
Hydraulic Shut-off
Valve (in closed
position)
Bleed Valve
R
GB
Flat Washer
Lock Nut
Hitch Lever
(unlocked position)
Sulky Cart
Pressure
Control Knob
4. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
5. Open the bleed valve by turning it fully counterclockwise.
6. Start the engine.
a. To start the gas
engine,
• move the fuel valve
lever to the open
position,
• move the throttle
lever to its middle
point,
• move the choke
lever to the closed
position for a cold
engine or to the open position for a warm engine,
• turn the engine switch to the ON position, and
• pull the starter rope briskly until the engine starts.
7. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent flows freely from the bleed
hose.
8. Allow the sprayer to run for 15–30 seconds to flush the
test fluid out through the bleed hose and into the waste
container.
9. Turn off the sprayer.
a. To turn off the gas engine,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the throttle lever to the slow position, and
• turn the engine switch to the OFF position.

Operator Controls

The following controls are used to control the operation of the
line striper.
Caster Trigger
The caster trigger controls the operation of
the front caster on the cart. It is located on
the left handle of the cart when standing
behind the sprayer. The front caster on
the cart is designed to track the sprayer in
either a straight line or allow free motion.
1. To lock the front caster in the
straight line position, squeeze
then release the caster trigger and move the sprayer
forward.
2. To allow free motion of the front caster, squeeze and
hold the caster trigger.
Gun Lever
The gun lever controls the operation of
the spray gun(s). It is located on the
right handle of the cart when standing
behind the sprayer, directly below the
handle grip. Squeezing the gun lever
will cause the spray gun(s) to spray.
Brake Lever
The brake lever stops the line striper
from moving forward or backward. It is
located on the right handle of the cart when standing behind the
sprayer, to the right side of the handle grip.
Forward/Reverse Switch
The forward/reverse switch controls the direction that the
PowrHandler drive system moves the line striper. It is located
on the left handle of the cart when standing behind the sprayer.
Pressing the forward side of the switch will move the line striper
forward. Pressing the reverse side of the switch will move the
line striper backward.
6
Choke Lever
Throttle
Lever
Engine
Switch
Fuel Valve
Starter Rope
Lever
Caster
Trigger
Gun Lever
Brake Lever
© Wagner. All rights reserved.