Hatco THERMMAX Salamander TMS2-1H Serie Manuel D'instructions page 3

Read the following important safety information before using this equipment to avoid
serious injury or death and to avoid damage to equipment or property.
WARNING
ELECTRIC SHOCK HAZARD:
• Unit must be installed by a qualified
electrician. Installation must conform
to all local electrical codes. Installation
by unqualified personnel will void unit
warranty and may lead to electric shock
or burn, as well as damage to unit and/or
its surroundings.
• Units supplied without an electrical plug
require field installation of proper plug.
Plug must be properly grounded and of
correct voltage, size, and configuration for
electrical specifications of unit. Contact
a qualified electrician to determine and
install proper electrical plug.
• Units supplied without an electrical cord
and plug require field installation of proper
cord and plug or a hardwired connection
to on-site electrical system. Connection
must be properly grounded and of correct
voltage, size, and configuration for
electrical specifications of unit. Contact
a qualified electrician to determine and
install proper electrical connection.
• When installing a hardwired unit, a 2-pole
or 3-pole switch (depending on unit)
must be installed between unit and main
electrical supply. The switch must be
rated properly and have contacts with a
minimum opening distance of 3 mm (1/8").
• Turn OFF power switch, unplug power
cord/turn off power at circuit breaker, and
allow unit to cool before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water.
Unit is not waterproof. Do not operate if
unit has been submerged or saturated
with water.
• Unit is not weatherproof. Locate unit
indoors where ambient air temperature is
a minimum of 21°C (70°F) and a maximum
of 29°C (85°F).
• Do not steam clean or use excessive
water on unit.
• This unit is not "jet-proof" construction. Do
not use jet-clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed
or worn.
• This unit must be serviced by qualified
personnel only. Service by unqualified
personnel may lead to electric shock or burn.
Form No. TMS2CEM-1021
IMPORTANT SAFETY INFORMATION
ELECTRIC SHOCK HAZARD:
• Do not attempt to repair or replace a damaged
power cord. Cord must be replaced by
Hatco, an Authorized Hatco Service Agent,
or a person with similar qualifications.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement
Parts when service is required. Failure to
use Genuine Hatco Replacement Parts
will void all warranties and may subject
operators of the equipment to hazardous
electrical voltage, resulting in electrical
shock or burn. Genuine Hatco Replacement
Parts are specified to operate safely in the
environments in which they are used. Some
aftermarket or generic replacement parts do
not have the characteristics that will allow
them to operate safely in Hatco equipment.
FIRE HAZARD:
• Install unit on and around non-combustible
surfaces
construction only. Ensure surface
construction has no combustible material
against underside. In all cases, such
construction shall extend at least 305 mm
(12") beyond equipment on all sides.
• Locate unit a minimum of 51 mm (2")
from any walls. If safe distances are not
maintained, discoloration or combustion
could occur.
• Do not obstruct air intake openings or
air exhaust openings on outer housing
of unit. Unit combustion or malfunction
may occur.
• Do not place anything on top of unit.
For wall mounting, use special wall mount
bracket provided with unit only. Secure wall
mount bracket to a solid, non-combustible
surface using appropriate hardware for
mounting surface and weight of unit.
Make sure all operators have been instructed
on the safe and proper use of the unit.
This unit is not intended for use by children
or persons with reduced physical, sensory,
or mental capabilities. Ensure proper
supervision of children and keep them away
from the unit.
This unit has no "user-serviceable" parts.
If service is required on this unit, contact
an Authorized Hatco Service Agent or
contact the Hatco Service Department at
+1-414-671-6350.
3
WARNING
with non-combustible