Publicité
Les langues disponibles
Les langues disponibles
Turning the power on/off
The power switch is located on the underside of the Robotic Mower.
Press the
side of the power switch to turn on the power, or
the
side to turn off the power.
► Fig.3: 1. Power switch
Charging the Robotic Mower
Checking the remaining battery capacity
1.
Press the "STOP" button.
The display cover opens.
► Fig.4: 1. "STOP" button 2. Display cover 3. Control panel
2.
Turn on the power switch of the Robotic Mower.
3.
Press the
button on the control panel.
The [Main menu] appears. You can check the remaining battery
capacity at the upper right of the screen.
Main menu
► Fig.5: 1. Remaining battery capacity indication
LCD screen indication
Charging
1.
Turn on the power switch of the Robotic Mower.
NOTE: Charging is performed only when the power switch of the
Robotic Mower is turned on.
NOTE: If the battery is fully discharged, it will take longer than usual
for the charging to begin.
NOTE: If the battery is hot or cold, charging will not begin.
2.
Dock the Robotic Mower with the charging station.
► Fig.6: 1. Charging station 2. LED
When charging starts, the LED blinks green. When charging is com-
plete, the LED turns off.
Things that should be understood before use
Work environment
Check that the area to be mowed by the Robotic Mower conforms to
the following items.
•
The grass height is 65 mm or less.
If the grass is too long, cut it down in advance.
•
There are no obstacles such as stones, sticks, or tools.
The Robotic Mower may fling or catch obstacles, resulting in an
accident.
•
There are no puddles.
The Robotic Mower can mow lawns in the rain, but wet grass
tends to stick to the Robotic Mower, and the possibility of slipping
on steep slopes increases.
•
There is no snow accumulation.
The Robotic Mower may slip and not operate correctly.
Remaining battery capacity
80 - 100 %
60 - 80 %
20 - 60 %
0 - 20 %
Charging station
The charging station charges the Robotic Mower and flows signals in
the boundary wire and guide wire.
Check that the location to install the charging station conforms to the
following items.
•
It is close to the power supply.
•
It is a level location.
The installation location has a slope within ±5° of level.
•
The location should be protected from the sun.
•
When installing the charging station on the lawn directly, keep
the lawn short.
•
There is a space of 3 m or more in front of the boundary wire.
NOTICE: Do not bend the station base.
Boundary wire
The boundary wire defines the area where the Robotic Mower is to
perform mowing work.
Install the boundary wire around the boundary of the area where the
Robotic Mower is to perform mowing work.
For the installation method, refer to the chapter "Installing the
Boundary Wire" in the Setup Guide.
Guide wire
This wire guides the Robotic Mower when it returns to the charging
station. This wire also guides the lawn mower to areas that the lawn
mower works less frequently due to topographical reasons, etc.
For the installation method, refer to the chapter "Installing the Guide
Wire" in the Setup Guide.
Lamp lighting
The Robotic Mower and the charging station indicate various states
by the lighting patterns of their lamps.
► Fig.7: 1. LED 2. Station indicator
Robotic Mower
LED
State
Green/blinking
Charging (Turns off when charging is complete)
White/blinking
Operating (Blinks for the time specified by the [LED]
setting)
Red/blinking
Error occurrence
Off
Standby/Power off
or other than the above
Charging station
Station indicator
State
Red/lighted
Error occurrence
Red/blinking
There is an abnormality in the boundary wire
connection
Green/lighted
The boundary wire is connected successfully
17
ENGLISH
Publicité
