Zipro Dunk Manuel D'utilisation page 13

EN
noises heard when rotating the pedals backwards occur for
technical reasons and have no negative consequences.
• Noise emissions are greater when loaded.
• Before each training, make sure the protective devices are
operational and bolt and plug connections are tight.
• Wear appropriate (sports) shoes during the training.
MAINTENANCE
Carry out maintenance activities at regular intervals. The tasks listed
below should be carried out at least every 20 hours of operation.
• Check moving parts of the device. If they need lubrication, use
a bicycle bearing grease.
• Check the conditions of such parts as bolts and nuts.
Make sure they are tight.
•
Wipe the sweat off the device after each training. Make sure
the display does not come in contact with water or moisture.
•
Clean the product with soapy water only. Do not use cleaning
agents.
• Store the device in a dry and warm place.
• Do not expose the device to direct sunlight.
ENVIRONMENT
The device is delivered in a package to protect it against any possible
transport damage. The packaging is made from non-processed
material and can be recycled. Throw the materials to appropriate
colour containers for selective waste collection.
Protect the environment and do not throw used batteries into
household wastes. Return them to the point of sale or a special
recycling centre.
ASSEMBLY DIAGRAM (→ See page 2)
ATTENTION! Do not use parts other than those provided by the manufacturer.
PARTS LIST
No. Description
1 Main frame
2 Front base
3 Rear base
4 Handlebar post
5 Steering wheel
6L/R Left/right handle
7L/R Handle arm, left/right
8L/R Pedal base, left/right
9 Front base cap
10 Hexagonal bolt
11 Handling wheel
12 Flat washer D8xφ16x1.5
13 Locknut M8
14 Hexagonal nut M10
15 Level foot
16 Flat washer φ10xφ20x2
17 Allen bolt M10*l58
18 Spring washer D10
19 Rear base cap
20 Crank
21 Washer φ22xφ28φ0.3
22 Allen bolt M8x16
23 Flat washer D8xφ20x2
24 Flat washer D8xφ38x2
25 Spring washer D8
26 Hexagonal bolt M10x20
27 Flat washer D10xφ20x2
28 Lower handle arm
29 Washer D40
30 Pedal base bearing
31 Pedal base cap
32 Pedal base sleeve
33 Hexagonal bolt M8x45
34L/R Left/right pedal
35 Bolt ST4.2x18
ASSEMBLY MANUAL
CAUTION! Follow the steps below during the assembly and use tools supplied with the product.
Prepare sufficient space for the assembly operation.
It is advisable to assemble the product with another person because of the weight of some elements.
13
Used electrical equipment (including the computer and power supply)
are recyclable. Do not throw them out with household waste as they
may contain substances dangerous to the health and environment. You
can actively contribute to sustainable use of natural resources and the
protection of the natural environment by handing the used device to
a recycling centre for used electrical devices.
ASSEMBLY
The device must be assembled carefully by an adult. In case of doubt,
ask a more experienced person for help.
•
Prior to the assembly, make sure the set contains all
the listed elements and whether none of the parts was damaged
during transport. If any parts are missing or you have any other
reservations, contact the seller.
• Have a look at the drawings and explanations and follow the
assembly manual when assembling the device.
•
Be careful during the assembly. There is a risk of injury when
using the tools and parts.
• Remember to keep your surroundings safe. Do not let tools and
parts lie around in chaos. Remember that plastic foil and bags
pose o suffocation risk to small children.
• Assembly parts necessary for a specific step in
the assembly manual are shown in pictures and included in
instructions. Use the elements indicated in the assembly
manual.
• Do not tighten parts completely during the first stages
of the assembly. Tighten connections after all parts are placed
and fitted properly.
• The manufacturer may have assembled some parts.
Quantity No. Description
1 36 Handle arm bearing
1 37 Bolt M8x80
1 38 Handle arm sleeve
1 39 Saddle height knob
1 40 Handlebar post and handle arms' sleeve
1/1 41 Handle bearing
1/1 42 Handle sleeve
1/1 43 Curved washer D8xφ19x1.5xr30
2 44 Bolt M8xl50
1 45 Handle foam
2 46 Handle cap
4 47 Computer
2 48 Handlebar cap
4 49 Hexagonal nut
4 50 Handlebar foam
8 51A/B Handlebar post cover, A/B
4 52 Bolt M4x10
6 53 Bolt ST3x15
2 54 AC adapter / Power socket
2 55L/R Pedal stabilising pad, left/right
2 56 Long axle
8 57 Handlebar angle adjustment knob
2 58 Handlebar post bottom cover
2 59 Computer cable
2 60 Connecting cable
2 61 Curved washer D8xφ20x2xr30
2 62 Heart rate sensor cable
2 63L/R Pedal base, left/right
2 64 Slotted-head bolt
2 65 Locknut M10
4 66 Water bottle
4 67 Water bottle holder
6 68 Screw
1/1 69 Flat washer
39
Quantity
4
2
2
2
2
4
2
4
4
2
2
1
2
4
1
1/1
4
6
1
1/1
1
1
1
1
1
2
2
1/1
1
2
1
1
2
2