Christopeit Sport SP5000 Instructions De Montage Et D'utilisation page 22

STEP 12
Installation of forearm pad (61), small back pad (62) and
handgrip 2 (30) at dipping bar (25) and support 1 (4).
1. Adjust the small back pad (62) on dipping bar (25) so that
the threaded holes in the rear of small back pad (62) are align
with dipping bar (25) and screw it tightly by using screw M8x20
(101), spring washer for M8 (123) and washer 8//16 (117).
2. Adjust the forearm pad (61) on dipping bar (25) so that the
threaded holes in the rear of forearm pad (61) are align with
dipping bar (25) and screw it tightly by using screw M8x55
(105), spring washer for M8 (123) and washer 8//16 (117).
3. Place the hand grips (30) into appropriate holder of dipping
bar (25) and screw them tightly by using screw M10x20 (108),
spring washer for M10 (122) and washer 10//20 (118).
4. Put the pre-assembled dipping bar (25) into appropriate
holder of support 1 (4) and screw it tightly into desired position
by using screw M10x70 (112), washer 10//20 (118) and self
locking nut M10 (124).
5. Then put the screw caps for M10 (131) onto all M10 screw
heads and nuts and the screw caps (132) for M8 onto all M8
screw heads and nuts.
STEP 13
Installation of Stepper and Crossbar (22) at support 1 (4).
1. Place the crossbar (22) into appropriate position at support
1 (4) and rear foot (2), so that the holes are align and screw it
tightly by using screw M10x70 (112), washers 10//20 (118) and
self locking nut M10 (124). (Perhaps you have to loosen the
connection point of support 1 (4) and rear foot (2) a little bit to
mount crossbar easy.)
2. Put the left and right pedal (21+24) in right direction at
appropriate holder at support 1 (4), that the steel bearings
align and slide the axle 1 (34) through. Secure the axle 1 (34)
by using screw M8x15 (99), spring washer for M8 (123) and
washer 8//38 (120) on both ends of axle.
3. Put the hydraulic cylinder (58) with top side onto the holder
of crossbar (22) and secure this position by using screw M8x15
(99), spring washer for M8 (123) and washer 8//28 (121).
4. Scew the bottom end of cylinder (58)at the holder for
cylinder (46) by using screw M8x40 (103), washer 8//16 (117)
and self locking nut M8 (125). Ensure that the cylinder (58) can
turn at holder a little bit.
5. Insert the holder for hydraulic cylinder (46) from top
side trough the pedal left and right (21+24) and connect the
holder (46) into desired position by using handgrip nut (75) and
washer 10//38 (120). You can adjust the stepper resistance at
holder (46) by choosing dierent positions at pedal let and right
(21+24). (Note! The selectable positions for the mounts for hy-
draulic cylinders (26) are specied by holes in the oot pedals
(10) and (11). The setting of the mount (26) should be in both
foot pedals (10) and (11) always the same. The settings can
be changed later at any time depending on the desired load.
The closer the setting position to the axis (34), the lighter the
stepper resistance for stepper training.)
6. Put a cable roller unit as gure „A" show together, put the
cable 5 (59) over the pulley (83) and connect this at cable
pulley holder incl. hook (35) in a way that the cable pulley can
roll easy.
7. Insert the cable pulley holder incl. hook (35) into the
welded holderat crossbars' (22) bottom side and connect the
ends of cable 5 (59) with the pedal left and right (21+24).
8. Then put the screw caps for M10 (131) onto all M10 screw
heads and nuts and the screw caps(132) for M8 onto all M8
screw heads and nuts.
61
30
131
117
118 123
105
122
108
132
131
A
118
124
83
84
118
84
131
110
99
123
121
99
123
120
58
132
103
117
46
24
120
125 131
75
59
Cable 5
560mm
22
132
101
123
117
118
124
118
4
62
25
131
131
4
124
35
118
A
59
34
117
132
124
118
22
118
112 131
2
GB
5
131
112
118
112
131
21