Display Functions - Nilfisk RS 851 Instructions D'origine

ENGLISH

Display functions:

1. When the key is turned to ON
When the ignition key (24, Fig. D) is turned to the fi rst
position, the display (17) shows for a few seconds the fi rst
page (23, Fig. H) with numbers or symbols that indicate
the machine condition. The parameters that can be
checked are shown below.
• Scheduled maintenance intervals.
MA0 (15, Fig. H) indicates the scheduled maintenance
at 150 hours, while MA1 (16) indicates the scheduled
maintenance at 500 hours. If one of the intervals
is nearly expired or expired (negative number),
maintenance procedures must be performed as shown
in the relevant chapter.
NOTE
When one of the maintenance intervals has
expired, one of the symbols (15 or 16, Fig.
H) fl ashes for a few seconds at machine
start-up.
• Enabled hydraulic system
WARNING!
If the symbol
the key
means that the maintenance interval
has expired. Proceed as shown in the
relevant chapter.
• Number of working hours
• Odometer (18, Fig. H).
• Alarm counter (17, Fig. H). It counts the number of
alarms occurred after the last reset of the control unit.
If the number is different from zero, contact a Nilfi sk
Service Center to reset the system.
• Software overhaul
• Road sweeper identifi cation number
The number "005" identifi es the RS 851 model, with
VM D703 IE3 engine.
• Fasten the seat belts
H) warns that the seat belts must be fastened.
2. Transport mode visualisation
When the key is turned to ON, the display (17, Fig. D)
automatically shows the transport mode visualisation (13,
Fig. H) thus replacing the screen (23). The screen (13, Fig.
H) remains even after the engine has been turned on. This
screen shows the following parameters.
• Machine speed : 3-digit number (1, Fig. H) with the
following symbol
Km/h
WARNING!
The speedometer sensor cannot be
checked for effi ciency, so the system
detects that the machine is stopped
even if the sensor is disconnected or
shorted, so the related safety systems
are disabled.
8
USER MANUAL
(21, Fig. H).
is not shown, but
appears on the display, it
(14, Fig. H).
(19, Fig. H).
(20, Fig. H).
. The fl ashing symbols (22, Fig.
(2).
33018305(3)2010-01 A
• Fuel level : the fuel level is shown by the horizontal
bar indicator (3, Fig. H). The last bars indicate the
reserve, they fl ash when the level is low. The fuel level
instantaneous value in % (5, Fig. H) is shown too.
CAUTION!
If the level sensor is faulty, the display
shows warning messages according to
the type of fault (short or open circuit)
(for the alarm coding see the Alarm
Description paragraph). To repair the
circuit and replace the level sensor,
contact a Nilfi sk Service Center.
The symbol (4, Fig. H) indicates that the fuel level
indicator is activated.
• Engine coolant temperature
shown by the horizontal bar indicator (6, Fig. H). The
bars fl ashes in case of overheating. The temperature
instantaneous value (8, Fig. H) is shown too. The
symbol (7, Fig. H) indicates that the temperature
indicator is activated.
CAUTION!
If the temperature sensor is faulty,
the display shows warning messages
according to the type of fault (short
or open circuit) (for the alarm coding
see the Alarm Description paragraph).
To repair the circuit and replace the
temperature sensor, contact a Nilfi sk
Service Center.
• Dust control system tank water level
relevant indicator (12, Fig. H):
– main tank and sub-tank are full
– main tank is empty and sub-tank is full
– main tank and sub-tank are empty. In this
condition, the dust control system and high-
pressure washing system turn off after about 5
seconds.
!
– the level sensors are faulty or exchanged.
• Machine operation mode
(11, Fig. H):
– transport mode
RS 851
: the temperature level is
with the
with the relevant indicator