Picking Up Liquids - Hilti VC 40 Mode D'emploi

2. Turn the control switch to the "ON" position.
7.3 Operation with use of the electric tool power
outlet
DANGER
The power outlet is to be used only to connect electric
tools directly to the vacuum cleaner.
NOTE
Check that the electric tool is switched off before plugging
it into the power outlet on the vacuum cleaner.
NOTE
The operating instructions and safety instructions for the
electric tool plugged into the power outlet on the vacuum
cleaner must be observed.
NOTE
Check to ensure that the maximum power drawn by the
electric tool is below the maximum permissible output of
the power outlet on the vacuum cleaner (please refer to
the "Technical data" section of the operating instructions
and information printed on the power outlet).
1. Disconnect the power tool supply cord plug from
the power outlet.
2. Plug the electric tool's supply cord into the power
outlet on the vacuum cleaner.
3. Plug the vacuum cleaner's supply cord into the
power outlet.
4. Turn the control switch to the "AUTO" position.
5. Switch on the electric tool.
NOTE The vacuum cleaner will continue to run for
a short time after switching off the electric tool in
order to ensure that all dust is removed from the
suction hose.
7.4 Picking up dry dust
NOTE
Before using the appliance to pick up dry dust, especially
dust from mineral materials, always check to ensure
that the correct dust bag (Hilti accessory) is fitted in the
container. The material collected can then be disposed
of cleanly and easily.
CAUTION
The material collected must be disposed of in accord-
ance with the applicable regulations.
CAUTION
Never use the appliance without a filter element.
CAUTION
When fitting the top section of the vacuum cleaner,
take care to avoid pinching your fingers or damaging
the supply cord.
Check to ensure that the filter element is dry. A damp
filter element will quickly become clogged when dry dust
is picked up with the appliance. For this reason, replace
All manuals and user guides at all-guides.com
the filter element with a dry filter element before using the
appliance to pick up dry dust.
7.4.1 Changing the paper dust bag / filter fleece
DANGER
Check that the bag has not been pierced through by
objects which may cause injury.
CAUTION
The material collected must be disposed of in accord-
ance with the applicable regulations.
1.
2.
3.
4.
5.
6.
7.
8.
9.
7.4.2 Changing the plastic dust bag 4
CAUTION
The material collected must be disposed of in accord-
ance with the applicable regulations.
1.
2.
3.
4.
5.
6.
7.
8.
9.

7.5 Picking up liquids

CAUTION
Never use the appliance without a filter element.
7.5.1 Before picking up liquids
1.
2.
Disconnect the supply cord plug from the power
outlet.
Open the two catches.
Lift the vacuum cleaner top section away from the
waste material container.
Carefully remove the paper dust bag collar from the
adapter and remove the filter fleece.
Close the slider at the dust bag collar (place the
cover over the filter fleece).
Clean the waste material container with a cloth.
Fit a new dust bag / filter fleece in the waste material
container.
Fit the vacuum cleaner top section onto the waste
material container.
Close the two catches.
Disconnect the supply cord plug from the power
outlet.
Open the two catches.
Lift the vacuum cleaner top section away from the
waste material container.
Use a cable tie to close the plastic dust bag below
the punched holes.
Remove the plastic dust bag.
Clean the waste material container with a cloth.
Fit a new plastic dust bag (see instructions printed
on it) in the waste material container.
Fit the vacuum cleaner top section onto the waste
material container.
Close the two catches.
Remove the dust bag from the waste material con-
tainer.
Check to ensure that the electrodes of the level
monitoring system are clean. Clean them with a
brush if necessary.
en
25