Consequently, it is necessary to take preventive
steps to eliminate possible damage due to high
levels of noise and stress from vibration. Maintain
the machine well, wear ear protection devices, an-
ti-vibration gloves and take breaks while working.
During a working day, you shall take frequent and
adequate breaks to prevent damage from vibrati-
on and damage to the ears.
WORKING AREA HAZARDS
Thoroughly inspect the whole work area and re-
move anything that could be projected by the ma-
chine, be a hazardous source or cause damage to
the machine (stones, branches, iron wire, bones
etc.). Check that there are no bystanders, animal
or items that could be damaged within at least 15
meters of the machine's range of action.
Work only in daylight, or with suitable artificial li-
ght, in good visibility conditions. Try not to cause
any noise disturbance, by only using this machine
at reasonable times of the day.
Take on a firm and well-balanced position. Where
possible, avoid working on wet, slippery ground
or in any case on uneven or steep ground that
does not guarantee stability for the operator or
proper operation conditions for the machine.
REMAINING HAZARDS
The machine was built using modern technology
and in accordance with recognized safety rules.
Even when all safety measures are in place, some
remaining hazards, which are not yet evident, may
be present. The operator should use common sen-
se and take necessary precautions to avoid risk
due to remaining hazards.
PRODUCT SPECIFICATIONS
INTENDED USE
This machine is designed and manufactured for
transferring water e.g. in greenhouses, orchards,
gardens. The clean water and high pressure pum-
ps are designed for pumping only clean water. The
chemical pumps are designed for pumping clean
water, weak acid base (PH 4-11) and high ignition
temperature liquids or sea water. The semi-trash
(sewage) pumps are designed for pumping clean
water or water containing soft solids of a diame-
ter not larger than 25,4mm. The trash (mud) pum-
ps are designed for pumping clean water or water
containing solids of a diameter not larger than
25,4mm to a degree up to 50%.
Any other use differing from the above-mentio-
ned ones could be hazardous, harm people and
damage things and the machine itself.
IMPROPER USE
The machine must not be used for pumping ha-
zardous materials, e.g. accumulation of inflam-
mable or explosive products, hot embers or com-
bustion material without a flame, lit cigarettes,
glass, sharp objects, metal objects, stones and
any other object that could be dangerous to the
machine itself as well as the operator, bystanders,
animals or property.
Other examples of improper use may include, but
are not limited, to operation of the machine:
Without the original accessories supplied by the
f
manufacturer.
With original accessories but in a way not in accor-
f
dance to the instructions.
Without original spare parts.
f
With unauthorized modifications.
f
By more than one person.
f
TECHNICAL DATA PAGE 66
IDENTIFICATION
GWP 40/79 PLUS (Fig. 1)
1. Fuel tank cap
2. Fuel tank
3. Starter grip
4. Throttle lever
5. Air filter
6. Fuel switch
7. Choke lever
8. Transport handle
9. Spark plug
10. Muffler
11. Pump priming cap
12. Suction port (inlet)
13. Pump drain plug
14. Engine oil drain plug
15. Engine oil dipstick
16. Discharge port (outlet)
17. ON / OFF switch
GWP 50/209 PLUS, GWP 50/212 PRO,
GWP 80/212 PRO (Fig. 2)
1. Frame
2. Pump priming cap
3. Discharge port (outlet)
4. ON / OFF switch
5. Engine oil dipstick
6. Starter grip
7. Fuel tank cap
8. Air filter
9. Muffler
10. Engine oil drain plug
11. Pump drain plug
12. Suction port (inlet)
13. Fuel tank
GWP 80/212 ST PRO (Fig. 3)
1. Frame
2. Pump priming cap
3. Pump cover T-type bolt
4. ON / OFF switch
5. Engine oil dipstick
6. Engine oil drain plug
7. Starter grip
8. Fuel tank
9. Fuel tank cap
10. Air filter
11. Muffler
12. Pump drain plug
13. Suction port (inlet)
14. Discharge port (outlet)
English | 19
www.ffgroup-tools.com