GRAUPNER mx-10 Hott Manuel De Programmation page 125

RX + GENERAL MODUL
BAT1 E FUEL F
0.0V
T1 +20°C
BAT2
0.0V T2 +20°C
BAT1 E FUEL F
0.0V
T1 +20°C
BAT2
0.0V T2 +20°C
If a General Engine module, Order No. 33610, or a
General Air module, Order No. 33611, is connected to
the receiver, then this screen provides a graphic display
of the data supplied by it. For more information on these
modules please see the Appendix, or refer to the pro-
duct on the Internet at www.graupner.de.
Depending on the types of sensor fi tted to the modules,
the display constantly shows the following data:
The actual voltage of up to two rechargeable batteries
(BAT1 and BAT2); the measured values from up to two
temperature sensors (T1 and T2) and a fueltank level
indicator.
At the right-hand edge the screen shows either an al-
ternating list of the actual cell voltages of a LiPo battery
with up to six cells, or the current altitude relative to the
location, climb / descent in m/1sec and m/3sec, current
in Ampere plus the actual voltage of the battery connec-
ted to the sensor.
The meanings are as follows:
Value
CELL V
1:0.00
BAT1 / BAT2
2:0.00
3:0.00
FUEL
4:0.00
E / F
5:0.00
6:0.00
T1 / T2
1500
CELL V
ALT
1500
+500m
0m1
ALT
0m3
0m1
POWER
14.8V
0m3
10.3A
450
POWER V.
A
450
RX + ELECTRIC AIRMODUL
BAT1
0.0V
BAT2
0.0V T2 +20°C
BAT1
0.0V
BAT2
0.0V T2 +20°C
Explanation
Battery 1 / Battery 2
Fuel level / Fueltank indicator
Empty / full
Temperature of sensor 1 / sensor 2
Cell voltage of cell 1 ... max. 6
RPM
Current altitude
m/1 sec climb / descent
m/3 sec climb / descent
Actual voltage of the drive battery
Actual current of drive battery
Actual used capacity
0.0V 0A CELL V
ALT +500m 1L0.00
0m/1s 2L0.00
0m/3s 3L0.00
4L0.00
T1 +20°C 5L0.00
6L0.00
7L0.00
0.0V 0A CELL V
ALT +500m 1H0.00
0m/1s 2H0.00
0m/3s 3H0.00
4H0.00
T1 +20°C 5H0.00
6H0.00
7H0.00
If an Electric-Air module, Order No. 33620, is connec-
ted to the receiver, then this screen provides a graphic
display of the data supplied by it. For more information
on this module please see the Appendix, or refer to the
product on the Internet at www.graupner.de.
Depending on the types of sensor fi tted to the module,
the display constantly shows the following data:
The actual voltage of up to two rechargeable batteries
(BAT1 and BAT2); the measured values from up to two
temperature sensors (T1 and T2); the current altitude
relative to the location, and the climb / descent of the
model in m/1sec and m/3sec; the centre of the screen
also displays the current actually being drawn from a
power source.
At the right-hand edge the screen shows an alternating
display of the actual cell voltages of the battery packs
(max. seven cells each) connected to balancer sockets
1 (L) or 2 (H).
The meanings are as follows:
Value Explanation
V Actual voltage
A Actual current
BAT1 / BAT2 Battery 1 / Battery 2
ALT Current altitude
m/1s m/1 sec climb / descent
m/3s m/3 sec climb / descent
T1 / T2 Temperature from sensor 1 / 2
CELL.V Cell voltage of cell 1 ... max. 14
L Balancer socket 1
H Balancer socket 2
Program description: Telemetry menu 125