Maintenance; Bath Additives; Spinning Jets Maintenance; Purging The Whirlpool System - Jacuzzi Luxury Serie Mode D'emploi

Bath aDDitiVes

NOte: Do not use oil or oil-based bath additives.
If you want to use any kind of bath additive, use only a small
amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath additives
may increase the level of accumulations of bath residue in the
whirlpool system. If excess accumulations persist, you should
discontinue use of these products.

sPiNNiNg Jets MaiNteNaNCe

with spinning jets)
If hair or other kind of debris gets caught in the bearings of
these jets, it could cause them to stop spinning. This may
require disassembly and cleaning. To do this, simply grab the
nozzle and pull straight out of the jet housing. The bearing
casing will be attached to the nozzle. These can be separated
by holding the casing and pushing the nozzle out from the rear
of the casing. After cleaning, reassemble in reverse.
Bearing casing
Push from
rear to remove
nozzle

PurgiNg the WhirLPOOL systeM

NOte: The Whirlpool system should be purged at least twice
a month.
To remove accumulations of bath residue from the whirlpool
system, it is recommended that a whirlpool bath be purged
at least twice a month. For best results, however, we
recommend that you purge your whirlpool bath after each
use using, Systems Clean™, our exclusive two-part plumbing
system cleaner made specifically for whirlpool baths.
Systems Clean™ is available through an authorized Jacuzzi
Whirlpool Bath distributor or by calling us direct at
1-800-288-4002.
Jacuzzi Luxury Bath Series: Installation and Operation
©

MaiNteNaNCe

systeMs CLeaN™ iNstruCtiONs
Refer to the instructions on the Systems Clean™ packet.
CautiON: Do not use while bathing. Use extreme caution
when handling this product.
Immediately after bathing and exiting the whirlpool bath, leave
the bath water in the tub and add more hot water. The water
level in the tub must be at least 2" (51 mm) above the highest
jet.
NOte: Inducted air from the hydromassage system will cause
the Systems Clean™ contents to foam increasing odor.
(Models equipped
Turn OFF the whirlpool air control or turn it to the lowest
setting and pour in the entire contents of Packet No. 1 ONLY
directly into the bath water. For best results, pour the System
Clean into the tub near the intake for the circulation pump and
be sure to avoid contact with your skin. Allow the whirlpool
to run for 30 seconds and then add Packet No. 2 ONLY. It is
important to use Packet No. 1 before Packet No. 2 to avoid
a strong odor. Allow the bath to run for 5 to 10 minutes then
drain the tub completely. Refill the tub with cold water and run
for 2 to 3 minutes. Drain completely and rinse off any residue.
Remember to reset the air valves to your bathing comfort
Nozzle
level.
DaNger: Harmful if swallowed. Eye irritant. Protect your
eyes, skin and mucus membranes from contact with this
product or its concentrated solution. A strong alkaline product
can cause severe burns to the eyes and skin.
If you have followed the standard purging instructions above
and still have an excess accumulation of bath residue and
desire an alternative cleaning mechanism, we recommend
Super Systems Clean™ Plus, manufactured by Stearns
Packaging, to rectify this condition. This may be obtained by
contacting us at 1-800-288-4002. It is recommended that you
follow the instructions provided by the manufacturer with the
product. Repeated use may be necessary. Super Systems
Clean™ Plus does not replace the necessity to regularly
purge your whirlpool system with Systems Clean™ Plus as
recommended.
©
Page 2 K339000Y • April 2008