Table des Matières
Publicité
3-1. Automation Hood
Dimensions
Length:
Width:
Height:
Weight
4-1. Selecting A Location
!
Only qualified persons should in-
stall, operate, maintain, and repair
this unit.
!
Installation must meet all National,
State, and Local Codes − have only
qualified persons make this installa-
tion.
!
Do not move or operate unit where it
could tip.
!
Do not use this equipment to sup-
port personnel, large tools, or other
material.
!
Be sure the floor or other structural
support will support the weight of
the equipment.
4-2. Hardware Kit List
Item
Part
No.
No.
Description
. . . .
1
. . . . . . .
602159
. . . .
Screw, 312−18x .75 Hexwhd.66d Stl Pld Slffmg Tap−Rw
. . . .
2
. . . . . . .
172684
. . . .
Nut, 312−18 .50hex .27h Stl Pld Sem Cone Wshr.76d
. . . .
3
. . . . . . .
108940
. . . .
Screw, 250-20 x .75 Hexwhd .61d Gr5 Pld
. . . .
4
. . . . . . .
152461
. . . .
Nut, 250−20 .44hex .23h Stl Pld Sem Cone Wshr.65d
. . . .
5
. . . . . . .
229678
. . . .
Screw, 250−20x .75 Button Hd−Soc Stl Pld
. . . .
6
. . . . . . .
010910
. . . .
Washer, Flat .406idx0.812odx.065t Stl Pld Ansi.375
. . . .
7
. . . . . . .
601965
. . . .
Screw, 375−16x1.00 Hex Hd−Pln Gr5 Pld Blk
. . . .
8
. . . . . . .
167788
. . . .
Nut, 375−16 .56hex .34h Stl Pld Sem Cone Wshr.88d
. . .
. . . .
9
. . . . . . .
080389
Screw, 312-18x1.00 Hexwhd.66d Stl Pld Slffmg Tap-rw
. . . .
10
. . . . . . .
108941
. . . .
Screw, 250-20x1.00 Hexwhd.61d Gr5 Pld
SECTION 3 − SPECIFICATIONS
550H / 750S Models
153-1/2 in. (390 cm)
102-1/2 in. (260 cm)
17-1/2 in. (44 cm)
355 lb (161 kg)
SECTION 4 − ASSEMBLY
!
Do not use equipment to support
site-installed ducts, interconnecting
piping, or electrical services. All
ducts, piping, or electrical services
supplied by others must be ad-
equately supported.
!
Use only mounting hardware spe-
cifically designed for the structure
or material supporting the equip-
ment. Follow the recommendations
and installation guidelines provided
by the manufacturer of the mounting
hardware (if applicable).
550HW / 750SW / 1100HW Models
Moving The Equipment
1
Lifting Eye
Use lifting eyes and hoist to move the as-
sembled unit. See Section 4-3G for addi-
tional lifting information.
Clearance
Maintain adequate clearance from heat
sources and avoid interference with utilities.
Ductwork
Select a location that ensures straight inlet
and outlet ducts and minimizes directional
changes in ductwork.
.
Torque assembly hardware as follows:
1/4 in. bolt = 6.3 ft-lb, 5/16 in. bolt = 13
ft-lb, 3/8 in bolt = 23 ft-lb.
Quantity
550H/750S
. . . . . . . . . . . .
24
. . . . . . . . . . . . . .
32
. . . . . . . . . . . . . . . . . . . . . . .
172
. . . . . . . . . . . . .
188
. . . . . . . . . . . . . . . . . . . . . . .
16
. . . . . . . . . . . . . . . .
12
. . . . . . . . . . . . . . . . . . . . .
12
. . . . . . . . . . . . . .
12
. . . . . . . . . . . .
16
. . . . . . . . . . . . . . . . . . . . .
40
153-1/2 in. (390 cm)
118-1/2 in. (301 cm)
17-1/2 in. (44 cm)
395 lb (179 kg)
1
300 965-7
Quantity
550HW/750SW/1100HW
. . . . . . . . . . . . . . . . . . . . .
24
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
32
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
172
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
188
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
16
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
12
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
12
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
12
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
16
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
40
. . . . . . . . .
OM-254 498 Page 12
Publicité
Table des Matières
