Technical Characteristics Of The Various Components Of The Product - Nice MhouseKit GD1N Instructions Et Avertissements Pour L'installation Et L'utilisation

TECHNICAL CHARACTERISTICS OF THE VARIOUS COMPONENTS OF THE PRODUCT

The product GD is produced by Nice S.p.a. (TV) I. In order to improve its products, Nice S.p.a. reserves the right to modify their technical characteristics
at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes. Note: all the techni-
cal characteristics refer to a temperature of 20°C.
DESCRIPTION
Type
Adopted technology
Peak thrust [corresponds to the force
necessary to move a leaf]
Nominal torque [corresponds to the
force necessary to keep a leaf moving]
Idling speed
Speed at nominal torque
Maximum frequency of cycles
Maximum continuous cycle time
Operating Limits
Power supply GD
Power supply GD/V1
Max. absorbed power
Insulation class
Emergency power supply
Flashing light output
Courtesy light
ECSbus output
"OPEN" input
"STOP" input
Radio aerial input
Maximum cable length
Remote control possibility
GTX4 transmitters memorised
Range of GTX4 transmitters
Programmable functions
Self-programmed functions
Operating ambient temperature
Use in particularly acid, saline or poten-
tially explosive atmospheres
Assembly
Protection rating
Dimensions / weight
Model GD1K
Electromechanical gearmotor for automated sectional and overhead doors incorporating a control
unit complete with radio receiver for "TX4" transmitters.
24Vdc motor, helical teeth reduction gear; drive guide with timing belt and mechanical release.
A transformer inside the motor but separated from the control unit reduces mains voltage to the
nominal voltage of 24Vdc used by the automation system.
10.8 Nm
[600 N]
5.4 Nm
[300 N]
0.10 m/s in "slow" speed mode
0.18 m/s in "fast" speed mode
0.05 m/s in "slow" speed mode
0.09 m/s in "fast" speed mode
(For a maximum of approx. 10 cycles per hour. A maximum of 5 cycles per hour
4 minutes (the control unit limits the continuous operation)
Its structural characteristics make it suitable for use on sectional and overhead doors with coun-
terweights that are within the dimensions and limits indicated in table 7
250 W
1 (a safety grounding system is required)
---
For visual signalling devices with 12V lamp, maximum 21W
12V lamp maximum 10W BA15 socket (automotive type lamp), stays on 60s after the manoeuvre
One output with a maximum
load of 1 ECSBus unit
For normally open contacts (the closing of the contact causes the "OPEN" command)
For normally open contacts and/or for 8.2kΩ constant resistance, or normally closed contacts
with recognition of the "normal" status (any variation from the memorised status causes the
52 Ω for RG58 or similar type of cable
Mains power supply: 30 m; inputs/outputs: 20m with aerial cable preferably shorter than 5m
(observe the directions regarding the minimum gauge and type of cable)
With GTX4 transmitters, the control unit can receive one or more of the following commands:
"OPEN", "Partial opening", "Open only" and "Close only"
Up to 150 if memorised in mode 1
From 10 to 50 m without aerial, from 50 to 100 m with aerial incorporated in the FL100 flashing
light. The range can vary if there are obstacles or electromagnetic disturbances, and is affected by
the position of the receiving aerial incorporated in the flashing light.
"Cycle" or "Complete cycle" operation (automatic closing)
The pause time in the "complete cycle" mode can be set at 10, 20, 40, 80 seconds
The sensitivity of the obstacle detection system can be selected from 4 levels
The operation of the "Open" command can be selected from 4 modes
Automatic detection of devices connected to the ECSBus Output.
Automatic detection of the type of "STOP" device (NO or NC contact or 8.2kΩ resistance)
Automatic detection of door length and calculation of deceleration points.
DATA
Model GD10K
0.10 m/s in "slow" speed mode
0.15 m/s in "fast" speed mode
0.05 m/s in "slow" speed mode
0.08 m/s in "fast" speed mode
50 complete cycles per day
is permitted at 50°C
230 Vac (±10%) 50/60 Hz
120Vac (±10%) 50/60Hz
with PR1 accessory
One output with a maximum
load of 6 ECSbus units
"STOP" command)
"Slow" or "fast" motor speed
-20 ÷ 50°C
NO
Horizontal
IP40
380 x 280 x h 110 mm / 4 kg
18 Nm
[1,000 N]
9 Nm
[500 N]
370 W
English – 27