Publicité
Les langues disponibles
Les langues disponibles
Troubleshooting
The table shows potential failures, their possible cause
and remedies. Call your specialist if you can not tackle
with the trouble.
Turn off and unplug the appliance before
maintenance and cleaning.
Electric shock hazard.
Symptom
Possible cause
Engine not
1.
Fuel tap is
starting.
closed
2.
No fuel
3.
Too weak
starter pulling
4.
Too big
distance of the
spark plug.
Loose, exposed
socket plug
5.
Loose socket
plug
6.
Too little oil in
the tank
Engine
1.
Too small
running
appliance.
irregularly.
Spark plug
system is not all
right.
2.
Wrong fuel
Generator
1.
Short-circuit
not
2.
Defective cable
generating
3.
Loose cable
current.
Safety instruction for inspections and servicing
Only a regularly serviced appliance may be a satisfactory
aid. Insufficient servicing and care may lead to unexpected
accidents and injuries.
Inspections and servicing
Regular cleaning and servicing are of essential importance for
perfect working and long service life.
Do not smoke when performing
works mentioned below. Never
Remedy
1.
Make sure the fuel
tap and the ON/OFF
switch are in the
"ON" position.
2.
Make sure there is a
sufficient amount of
fuel in the tank.
3.
Pull the starting
cable stronger.
4.
Make sure the spark
plug is fitted
properly.
5.
Make sure the spark
plug has been
installed properly
and the spark plug
cable is on the plug.
Clean the plug and
check the electrodes
distance if
appropriate.
6.
Add oil.
1.
Make sure the
spark plug is fitted
properly and the
spark plug cable is
on the plug. Clean
the plug and check
the electrodes
distance if
appropriate.
2.
Make sure
appropriate fuel has
been used.
1.
If the signal
indicator is not on, it
is a failure you are
unable to remove. If
the signal
indicator is on:
2.
Press the overload
protection for the
used output.
3.
Check the
connection.
4.
Check whether it is
short circuit or
overload.
work near sparks, flames or open fire.
Service and inspect the appliance at regular intervals.
Air filter
The air filter should be cleaned every 50 running hours.
Loosen the 2 hex head screws.
Remove the lid.
Remove the air filter.
Clean the filter with alcohol or ethanol.
Drop small amount of oil on the air filter and press it.
Insert the filter insertion again and fit the cover.
Fuel filter
Remove the filling hole lid.
Take the fuel filter off the filling hole.
Clean the filter with alcohol or ethanol.
Dry it with a soft cloth.
Refit the filter to the filling hole.
Put the lid back to the filling hole.
Spark plug (see pic. 5)
Remove the cable from the spark plug (14).
Remove the spark plug using the spark plug wrench.
Clean the electrode with a wire brush.
Check the electrodes distance (correct value: 0.7 to
0.8 mm) and adjust it if necessary.
Refit the spark plug.
Oil change
Let the engine warm up.
Unscrew the filler plug.
Remove the drain plug and empty the used
oil to an appropriate container.
Check the sealing and replace it if
necessary. Screw the drain plug and add
new oil.
Refit the filler plug.
Noise suppressor inspection
Let the noise suppressor cool down.
The noise suppressor could be clogged
with filter parts.
Unscrew the lid and remove the cover.
Clean the surface with a wire brush.
Replace it if necessary.
Inspection and servicing schedule
Time interval
Description
Check the spark plug
Every 3 months
state; set the distance
and clean it
Every time you
Check the engine oil
are going to use
level
the appliance
After 1 month
and after 6
Change the engine oil
subsequent
months
Every 3 months/
Clean the air filter or
50 running hours
replace it if necessary
Clean the fuel tap and
Every 6 months
filter and replace them
if necessary
Check the distance of
Every 12 months
valves and adjust it if
necessary.
Check whether the fuel
Every time you
hose has any cracks or
are going to use
other damage and
the appliance
replace it if necessary.
More details
After the
engine has
cooled down
15
Publicité
