Specifications; Trouble Shooting - Numatic CRG 8055/100T Notice Originale

(Empty) Net Weight
Brush Weight
120 A/Hr
CRG 8055 - 200 kg CRG 8055 - 17 kg
CRG 8072 - 220 kg CRG 8072 - 32 kg
Run Time
Transaxle
2 x 120 A/Hr
24 V
3 Hrs
400 W
Brush Speed
150 rpm 24.2 L/sec
Hand Arm Vibration
Travelling (Quarry Tiles)
1.84 m/s
2
(Uncertainty 0.92 m/s )
2
ISO 5439-1
PROBLEM
Machine will not operate
Vacuum will not operate
Poor water pick-up
No brush / scrub function
Little or no water flow
Machine just 'stops' during
operating
Failure to rectify the problem or in the event of a breakdown contact your Numatic dealer or
32
www.numatic.co.uk
Brush Width
550 mm
370mm x 2
Run Time
2 x 100 A/Hr
2 Hrs
Airflow Transit Speed
0-6 Km/hr
Whole Body Vibration
Travelling (Quarry Tiles)
1.11 m/s
2
(Uncertainty 0.56 m/s
ISO 2431-1
CAUSE
Missing or blown fuses
Low battery charge
Machine is connected and charging
Key is off or missing
Handle safety fuse blown
Missing or blown fuse
Vacuum switch not engaged
Waste water tank full
Waste water tank full
Clogged / blocked vacuum hose
Loose hose connections
Debris basket filter clogged / blocked
Separator filter clogged / blocked
Poor separator seal
Damaged separator seal
Damaged / split vacuum hose
Damaged floor tool blades
Low battery charge
Floor tool incorrectly adjusted
No brushes fitted
Brush deck raised
Missing or blown fuses
Clean water tank empty
Clean water tank filter blocked / clogged
Water flow not on
Brush deck raised
Blown pump fuse
Brush motor fuse blown due to high load
Handle safety fuse blown
Numatic Technical helpline +44 (0)1460 269268
Model - CRG 8055 / 8072
Brush Pad
Pressure Width
8.4 G/cm 508 mm
2
19.9 G/cm 360mm x 2
2
Total Battery Total Battery
Weight 120 A/Hrs Weight 100 A/Hrs
74 kg
(163 lbs)
Capacity Water Flow Rate
0 - 3
80L / 80L
L/min
Height
1160 mm
)
2
SOLUTION
Fit or replace fuse (page 3 & 5)
Charge batteries (page 15 / 16)
Take off charge (page 15)
Insert key & turn to operating position
Replace fuse - No 19 (page 2 / 3) (or contact service engineer)
Fit or replace fuse (page 3 & 5)
Press switch (page 9)
Empty waste water tank (page 12)
Empty waste water tank (page 12)
Remove and clean (page 12)
Push tight connections (page 6)
Remove and clean (page 13)
Remove and clean (page 12)
Clean and refit (page 12)
Renew (contact service dept)
Renew (contact service dept)
Renew (contact service dept)
Re-charge batteries (page 15 / 16)
Adjust floor tool (page 11)
Check and fit (page 7)
Lower brush deck (page 7 & 11)
Fit or replace fuse (page 3 & 5)
Fill clean water tank (page 8)
Remove and clean (13)
Switch on water flow (Page 9)
Lower brush deck (page 7 & 11)
Replace fuse - No 20 (page 2 / 3)
Replace fuse & reduce load (page 3 & 5)
Replace fuse - No 19 (page 2 / 3) (or contact service engineer)
(UK) Specifications
Pad
Brush Motor
Pressure
6.8 G/cm
2
16.6 G/cm
2
Charge Times
2 x 120 A/Hrs
62 kg 10A = 12 Hrs
(136 lbs) 20A = 7 Hrs
Cleaning Area
CRG 8055 - 1700m
2
CRG 8072 - 2200m
2
Length Width
CRG 8055 - 805 mm
1460 mm
CRG 8072 - 948mm

Trouble Shooting

Vac
Motor
24 V 24 V
600 W 400 W
Charge Times
2 x 100 A/Hrs
10A = 8 Hrs
20A = 5-6 Hrs
Sound Pressure
@ 3.5 K/Hr
≤ 70dB (A)
@ 3.5 K/Hr
Max Gradient
11%