Specifications - Numatic TRG 720/200T Notice Originale

❦
(Empty) Net Weight
Brush Weight
200 Ah / 300 Ah
TRG 720 / 200 - 357 kg
TRG 720 / 300 - 422 kg
Gross weight
Drive
200 Ah / 300 Ah
Motor
120L + 80kg operator
TRG 720 / 200 - 557 kg
24 V
700 W
TRG 720 / 300 - 622 kg
Brush Speed Air Flow
2-Stage 24.2 L/Sec
150 rpm
3-Stage 30 L/Sec
Hand Arm Vibration
Travelling
(Cleaning Mode)
ah ≤ 2.5m/s
2
ISO 5439-1
PROBLEM
Machine will not operate
Vacuum will not operate
Poor water pick-up
No brush / scrub function
Little or no water flow
Machine just 'stops' during
operating
Failure to rectify the problem or in the event of a breakdown contact your Numatic dealer or
Model - TRG 720 200T / 300T
Brush Width
720mm
32 kg
(2 x 370mm)
Max Run Time Max Run Time
200Ah 24V 300Ah 24V
(4 x 100Ah) (6 x 100Ah)
3.5 Hrs
Transit Speed
0-6 Km/hr
Whole Body Vibration
Travelling
(Cleaning Mode)
aw ≤ 0.5m/s
2
ISO 2431-1
CAUSE
Missing or blown fuses
Low battery charge
Machine is connected and charging
Key is off or missing
Handle safety fuse blown
Missing or blown fuse
Vacuum switch not engaged
Waste water tank full
Waste water tank full
Clogged / blocked vacuum hose
Loose hose connections
Debris basket filter clogged / blocked
Separator filter clogged / blocked
Poor separator seal
Damaged separator seal
Damaged / split vacuum hose
Damaged floor tool blades
Low battery charge
Floor tool incorrectly adjusted
No brushes fitted
Brush deck raised
Missing or blown fuses
Clean water tank empty
Clean water tank filter blocked / clogged
Water flow not on
Brush deck raised
Blown pump fuse
Brush motor fuse blown due to high load
Handle safety fuse blown
Numatic Technical helpline +44 (0)1460 269268
Brush Pad
Pressure Width
700mm
19.9 G/cm
2
(2 x 360mm)
Battery Weight
200Ah 24V
(4 x 100Ah)
5.5 Hrs 124Kgs
Capacity Water Flow Rates
120L /
0 - 3.5 L/min
120L
Height Length
1385 mm 1752 mm
SOLUTION
Fit or replace fuse (page 3 / 5 & 13)
Charge batteries (page 15 / 16)
Take off charge (page 15)
Insert key & turn to operating position (page 5 & 9)
Replace fuse - (page 2 / 3 & 13) (or contact service engineer)
Fit or replace fuse (page 3 / 5 & 13)
Press switch (page 11)
Empty waste water tank (page 12)
Empty waste water tank (page 12)
Remove and clean (page 12)
Push tight connections (page 3 / 6 / 12)
Remove and clean (page 12)
Remove and clean (page 12)
Clean and refit (page 12)
Renew (contact service dept)
Renew (contact service dept)
Renew (contact service dept)
Re-charge batteries (page 16 / 17)
Adjust floor tool (page 6 / 11)
Check and fit (page 7)
Lower brush deck (page 7 & 11)
Fit or replace fuse (page 3 & 5)
Fill clean water tank (page 8)
Remove and clean (13)
Switch on water flow (Page 9)
Lower brush deck (page 7 & 11)
Replace fuse - (page 2 / 3 & 13)
Replace fuse & reduce load (page 3 / 5 & 13)
Replace fuse - (page 2 / 3 & 13) (or contact service engineer)

Specifications

Pad
Brush Motor
Pressure
24 V
16.6 G/cm
2
600 W
Battery Weight Charge Times
300Ah 24V 200Ah 24V
(6 x 100Ah) (4 x 100Ah)
20A = 8 - 10 hrs
186Kgs
25A = 6 - 8 hrs
Cleaning Area
2200m @ 3.5 K/Hr
2
Width Ingress Protection
948 mm IPX3
Trouble shooting
T (+ 44) 01460 68600
Vac
Motor (24V)
2 - Stage: 400W
3 - Stage: 600W
Charge Times
300Ah 24V
(6 x 100Ah)
20A = 12 - 14 hrs
25A = 9 - 11 hrs
Sound Pressure
≤ 70dB (A)
Max Gradient
11%
37