Machine Cleaning And Disinfection - Dräger CPS 7900 Notice D'utilisation

Troubleshooting
CAUTION
!
Strictly follow the Instructions for Use of the
disinfectant!
The chemical protective suit may be damaged if
excessive amounts of disinfectant are used or if it is
exposed to the disinfectant for longer than indicated in
the respective Instructions for Use.
9. Thoroughly rinse all parts in clear water.
10. Drying of chemical protective suit (see Chapter 7.3.3 on
Page 28).
7.3.2

Machine cleaning and disinfection

The following accessories are required for machine cleaning:
Industrial washing machine Dräger CombiClean or
washing machine similar in construction
Washbag
Supporting disc
The industrial washing machine must have the following
characteristics:
Drum capacity >130 liters (>34.3 US gal)
Drum diameter >60 cm (>23.6 in)
Door opening >37 cm (>14.5 in)
Programmable controls
Electronic temperature control ±2 °C ( ±7 °F)
Drum revolutions: max. 4 revolutions/minute (2 slow
revolutions in one direction, 20 seconds idle time, 2 slow
revolutions in the other direction)
Clean and disinfect chemical protective suit as follows:
1. If the chemical protective suit is equipped with glove
combination 2, remove and dispose of the glove
combination (see Chapter 7.7.2 on Page 30). Replace by a
new glove combination.
2. If fitted, disassemble antifog visor, clean separately and
disinfect in immersion bath. Thoroughly rinse all parts in
clear water after cleaning.
CAUTION
!
Do not immerse antifog visors longer than 5 minutes,
otherwise the antifog coating will come off.
3. If fitted, remove, clean and disinfect ventilation unit and D-
connect.
4. If fitted, remove backpack pad and clean separately in
clear, warm water.
5. Remove the protective caps, the covers of the suit valves
(if fitted), and the valve discs from the suit valves. Clean
valve discs separately in clear, warm water.
6. Fully open the fastener system of the chemical protective
suit.
7. Place chemical protective suit on a clean working surface
and smoothen out any creases.
8. Place supporting disc in the hood, ensure that the visor is
flush to and congruent with the supporting disc.
28
9. Pull the washbag over the hood and ensure that the
washbag foam rests on the visor and the corded edge of
the washbag covers the lower edge of the visor. Pull cord
tight and close with a knot.
10. Fold socks or safety boots up twice. Avoid sharp bends.
11. Lay sleeves across the middle of the chest part. Smooth
out any creases.
12. Fold the hood with the washbag and the upper section of
the chemical protective suit to ensure that the visor lies on
the rolled-up safety boots. Smooth out any creases. Make
sure that the visor doesn't get deformed.
13. Place the chemical protective suit in the industrial washing
machine. Make sure that the section with the safety boots
is adjacent to the washing drum.
14. Start washing program "chemical protective suit".
CAUTION
!
Make sure that the washing drum only moves when it
is filled with water to avoid damaging the chemical
protective suit.
Maintain the following parameters during washing:
Detergent dose for one stage of the washing program:
5 g Eltra/1 liter of fresh water (0.18 oz./33.8 fl. oz)
Water temperature 60 °C ... 64 °C (140 °F ... 147 °F)
4 rinse cycles
15. Dry the chemical protective suit.
7.3.3 Drying of chemical protective suit
CAUTION
!
The chemical protective suit must not be spin-dried to
avoid damage.
The chemical protective suit must be completely dried
e. g. to avoid the formation of mold.
1. Remove any excess liquid from the chemical protective
suit, e.g. with a sponge, before drying.
2. Dry all internal and external parts thoroughly.
The chemical protective suit can be dried by blowing with
dry, oil-free compressed air or in a suit-drying cabinet
– maximum temperature: 40 °C (104 °F)
– minimum time: 120 minutes
Avoid exposure to direct heat or continuous sunshine.
NOTICE
i i
Suitable equipment for the drying of chemical
protective suits:
Dräger CombiDry
Dräger HTA-TA-CSA
TopTrock SF01 with fan GF
drying equipment identical in construction
3. Reinsert the backpack pad if applicable.
4. Carry out a visual inspection of the chemical protective suit,
visor, safety boots and gloves.
5. Reinsert the antifog visor if applicable.
Dräger CPS 7900