Stannah 600 Manuel D'installation page 27

GB Certificate of Test and Examination after Installation of 600 Model Stairlift to ensure Compliance with
Machinery Directive (2006/42/EC) Low Voltage Directive (2006/95/EC), EMC Directive (2004/108/EC)
Name and Address of User / Installation site: ................................................................ Tel: .......................
1. Description
a) Manufacturer:
b) Stairlift reference number:.................................... Chair batch No. ..................................... Carriage batch No...............................
c) Safe Working Load
d) Rated speed:
e) Motor tested on assembly:
f) Control actuator type:
Electrical Tests
2.
a) Electrical supply voltage at time of test:
b) Battery voltage:
c) Functional overload protection test:
d) Tripping time:
e) Control voltage:
f) Mains fuse rating:
3. Battery Checks
a) Battery charge voltage:
b) Confirm battery enclosure is vented:
c) Confirm batteries are securely fitted:
4. Mechanical / Operation Test
SWITCH OPERATION
a) Confirm all on / off stop switches operate correctly:
b) Confirm all control limits operate correctly:
c) Confirm final limits operate correctly:
d) Confirm all sensitive edges / surfaces operate correctly:
e) Confirm underside sensitive surfaces operate correctly and to the appropriate direction of travel
f) Tests to verify the function of the Overspeed Governor and Safety Gear
g) Confirm that all interlock switches operate correctly
h) Confirm that hinge position switch operates correctly
COMPONENT FUNCTIONING
j) State the stopping distance of the carriage with rated load upon application of the brake:
k) Confirm hand winding controls operate correctly:
l) Confirm Overspeed Governor has been subjected to factory test for correct tripping speed:
m) Carry out Installation overload testing
n) If an alarm is fitted, confirm mode of operation and that the system operates correctly:
o) Confirm clearance of at least 100mm between chair arms and any part of fixed installation whilst in travel position.
p) State distance of footrest above floor level: not to exceed 170mm
5. Confirmation
Confirm operating instructions have been handed to the user and the user has been instructed on use of stairlift:
6. Declaration
We certify that on (DATE) ............................................. this stairlift was thoroughly examined and found to be free from obvious defects
and that the foregoing is a correct report of the results.
Signed: ............................................................... Position / Qualifications: ......................................................
Installation Office / Branch Address: ..................................................................................................................................................
Stannah Stairlifts Ltd
24 to 52 degrees = 160kg (352lbs)
24 to 52 degrees = 135kg (297lbs)
0.1m/s
YES
Constant pressure controls
............V AC
............V DC
YES / NO
......... Seconds
24V DC
............ Amps
YES / NO
YES / NO
CE Directives:
g) Model type:
h) Type of motor:
i) Motor protection (type):
j) Type of drive:
g) Polarity check:
h) 0-volt rail connected and continuity tested:
i) Confirm battery polarity check:
j) AC supply frequency:
k) Phase:
l) Motor reversal delay:
V DC d) Confirm batteries are fully charged:
e) Confirm no leak when battery is fitted:
f) Confirm off charge indicator is functional:
(e.g on rotating seat, chair arm isolation
Upper ......... mm
Siena / Starla Manual and Powered Swivel
SL Manual & Powered Swivel
600
DC
Electronic
Rack and pinion
L-N = .......... L-E = ..........
+ ve ....
(alarm active unless fully raised)
Up ............mm
Lower ............ mm Intermediate ...... mm
N-E = ..........
YES / NO
- ve ....
............Hz
Single
............ Seconds
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
etc)
YES / NO
Down ............mm
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO
YES / NO