Product Description - SOMFY Ixengo L 24V Manuel D'installation

EN
WARNING
Take care when using the manual unlocking device.
Manual unlocking may result in uncontrolled movement
of the gate.
A er installation, ensure that:
• the mechanism is correctly adjusted
• the manual unlocking device is operating correctly
1.8. Regulations
Somfy declares that the product described in these
instructions, when used in accordance with these instructions,
complies with the essential requirements of the applicable
European directives and, in particular, with the Machinery
Directive 2006/42/EC.
The full text of the EC declaration of conformity is available on
the following website: www.somfy.com/ce.
Antoine CREZE, Head of Regulations, Cluses
1.9. Assistance
You may encounter difficulties or have questions when install-
ing your motorisation.
Do not hesitate to contact us; our specialists are on hand to
answer all your questions.
Internet: www.somfy.com

2. PRODUCT DESCRIPTION

2.1. Composition of the standard pack - Fig. 1
No. Quantity
1 2 Ixengo L 24V motorisation
2 2 Pillar mounting bracket
3 2 Pillar mounting bracket-motor connecting pin
4 2 Gate leaf mounting bracket
5 2 Washer and circlips
6 4 Unlocking key
1 Control box
* The contents may vary depending on the pack
2.2. Dimensions - Fig. 2
2.3. Field of application - Fig. 3
This motorisation is designed for motorising hinged gates with a rigid
structure (wood, metal, aluminium), with the following maximum dimen-
sions:
Weight per gate leaf
Width per gate leaf
Attention
For a large gate leaf format (larger than 2 m) or in a windy area,
Somfy recommends installing an electric lock.
Installing stops on the ground is not mandatory.
4
Description
400 kg 300 kg 170 kg
2.6 m 3 m 4 m
3. INSTALLATION
3.1. Defining the dimensions for inward opening -
Fig. 4
3.1.1. Using the Access Fix&GO Pro
The "Access Fix&GO Pro" application provides the information necessary to
install the motor correctly.
The basic data are:
• A gate leaf 50 mm thick (if the gate leaf is thicker, the opening angle
data will be reduced)
• The minimum width of the pillar is 80 mm
• The value x is between -60 mm and 180 mm
• The width of the gate leaf is between 950 mm and 4000 mm
• The opening time information is given for information purposes for
a 90° opening; the calculation was made using the maximum motor
speed with no slowing.
• The closure holding force information is given for information pur-
poses on a scale of 1 (weak holding force) to 7 (strong holding
force).
• The position of the mounting bracket on the pillar is given for the
smoothest possible movement with A close to B where possible.
3.1.2. Using the dimensions tables
No.
A-B Dimension to determine the mounting point of the pillar
mounting bracket
Recommendation A=B
X Distance between the gate axis and the edge of the pillar
Z Distance from the edge of the pillar to the motor's rotation
axis (length of the mounting bracket)
D Distance between the edge of the mounting bracket and the
inside edge of the pillar
Y Distance between the gate axis and the inside edge of the
pillar
α° Opening angle of the gate
1) Define the required opening angle α°.
2) Measure the dimension X on the gate.
3) Calculate B = Z + X (with Z = 110 mm for the standard mounting brack-
et).
4) In the table of dimensions, define the dimension A according to the
required opening angle α° and the calculate dimension B.
Attention
Having similar values for A and B will ensure the gate's movement
is more fluid.
As the values for A and B get further apart, the gate's movement
becomes less fluid, and the force exerted on gate will vary more.
The higher the value B, the greater the force required for closing.
To increase the value for dimension B, use a long mounting bracket
where Z = 240 mm (ref. 9019500)
Dimensions chart for use of the standard bracket 9019511 - Fig. 4a
Dimensions chart for use of the adjustable bracket 9019503 - Fig.
4b
Description
©
Copyright 2017 SOMFY ACTIVITES SA. All rights reserved.
IXENGO L 24V