Korg PA 900 Guide De L'utilisateur page 454

107: Cho/Flng - Mt.Dly
(Chorus/Flanger - Multitap Delay)
This effect combines a mono chorus/flanger and a multitap
delay.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
Chorus/Flanger
+
Chorus/Flanger
EQ LEQ HEQ
Trim
Feedback
Right
LFO: Tri / Sine
CHORUS/FLANGER
[F]LFO
0.02...20.00
Frequency [Hz]
a
LFO Waveform Triangle, Sine
[F]Delay Time
0.0...1350.0
[msec]
b Depth 0...100
Feedback –100...+100
c [F]EQ Trim 0...100
[F]PreLEQ Gain
–15...+15
[dB]
d
PreHEQ Gain
–15...+15
[dB]
–Wet...–1 : 99,
[F]Cho/Flng
e Dry,
Wet/Dry
1 : 99...Wet
MULTITAP DELAY
[D]Tap1 Time
0.0...1360.0
[msec]
a
Tap1 Level 0...100
[D]Tap2 Time
0.0...1360.0
[msec]
b
Feedback –100...+100
[D]High Damp
c 0...100
[%]
[D]Mt.DelayWe Dry, 1:99...99:1,
t/Dry Wet
d Src Off...Tempo
Amt –100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
e
Src Off...Tempo
Amt –100...+100
FX Amt
Multitap Delay
Feedback
Delay
(2)
Cho/Flng (1) Mt.Dly
High Damp
FX Amt FX Amt
FX Amt
Sets the speed of the LFO
Selects the LFO Waveform
Sets the delay time
Sets the depth of LFO modulation
Sets the feedback amount
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the effect balance of the
chorus/flanger
Sets the Tap1 delay time
Sets the Tap1 output level
Sets the Tap2 delay time
Sets the Tap2 feedback amount
Sets the damping amount in the
high range
Sets the multitap delay effect
balance
Selects the Wet/Dry modulation
source for the multitap delay
Sets the Wet/Dry modulation
amount for the multitap delay
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
108: Phaser - Cho/Flng
(Phaser - Chorus/Flanger)
This effect combines a mono phaser and a chorus/flanger.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Phaser
+
Phaser
EQ
LEQ HEQ
Trim
Phaser
Resonance
FX Amt
Right
LFO: Tri / Sine
PHASER
[P]LFO
Frequency [Hz] 0.02...20.00
a
LFO Waveform Triangle, Sine
[P]Manual 0...100
b Depth 0...100
Resonance –100...+100
-Wet, -
[P]Phaser Wet/
c 1:99...Dry...99:1
Dry
, Wet
CHORUS/FLANGER
[F]LFO
Frequency [Hz] 0.02...20.00
d
LFO Waveform Triangle, Sine
[F]Delay Time
0.0...1350.0
[msec]
e Depth 0...100
Feedback –100...+100
f [F]EQ Trim 0...100
[F]PreLEQ Gain
–15...+15
[dB]
g
PreHEQ Gain
–15...+15
[dB]
-Wet, -
[F]Cho/Flng
1:99...Dry...99:1
Wet/Dry
, Wet
h
Src Off...Tempo
Amt –100...+100
[F]Output Normal,
i
Mode Wet Invert
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src Off...Tempo
Amt –100...+100
Page 440
FX Amt
Chorus/Flanger
Chorus/Flanger
Normal
+
Output Mode
–
Feedback Wet Invert
Cho/Flng
FX Amt
FX Amt
LFO: Tri / Sine
Sets the speed of the LFO
Selects the LFO Waveform
Sets the frequency to which the
effect is applied
Sets the depth of LFO modulation
Sets the resonance amount
Sets the phaser effect balance
Sets the speed of the LFO
Selects the LFO Waveform
Sets the delay time
Sets the depth of LFO modulation
Sets the feedback amount
Sets the EQ input level
Sets the gain of Low EQ
Sets the gain of High EQ
Sets the effect balance of the
chorus/flanger
Selects the Wet/Dry modulation
source for the chorus/flanger
Sets the Wet/Dry modulation
amount for the chorus/flanger
Selects the output mode for the
chorus/flanger
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source