Table des Matières
Publicité
22: Bass Amp+Cabinet
(Bass Amp Model+Cabinet)
This simulates a bass amp and speaker cabinet.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
+
Bass Amp Model1
Right
D
-mod
LA STUDIO,
JAZZ ,
GOLD PANEL,
a
Amp Type
SCOOPED,
VALVE2, VALVE,
CLASSIC
Volume
0...100
Src
Off...Tempo
b
Amt
–100...+100
c
Bass
0...100
Middle
0...100
d
Mid Range
0...4
e
Treble
0...100
f
Presence
0...100
g Cabinet
Off, On
Simulater
LA - 4x10,
MODERN -
4x10,
METAL - 4x10,
CLASSIC -
8x10,
UK - 4x12,
STUDIO - 1x15,
h Cabinet Type
JAZZ - 1x15,
VOX AC100 -
2x15,
US - 2x15,
UK - 4x15,
LA - 1x18,
COMBI - 1x12
& 1x18
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
a: Amp Type
h: Cabinet Type
Recommended Combinations of Bass Amp Models and Cabi-
nets:
Amp Type
LA STUDIO
JAZZ
GOLD PANEL
SCOOPED
VALVE2
VALVE
CLASSIC
FX Amt
Volume
Cabinet Simulator
FX Amt
Selects the type of the amplifier
Sets the output level
Selects the modulation source for
the output level
Sets the modulation amount of the
output level
Sets the bass (low range) level
Sets the middle (mid range) level
Sets the mid-frequency range
Sets the treble (high range) level
Sets the presence (high-frequency
tone)
Switches the cabinet simulator on/
off
Selects the cabinet type
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
Cabinet Type
LA - 4x10, LA - 1x18
JAZZ - 1x15
MODERN - 4x10
METAL - 4x10
CLASSIC - 8x10
CLASSIC - 8x10
COMBI - 1x12 & 1x18
23: Tube PreAmp Model
(Tube PreAmp Modeling)
This effect simulates a two-stage vacuum tube preamp. You can
make individual settings for two vacuum tubes connected in
series. This lets you create the warm sound typical of vacuum
tubes.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
+
Tube Pre Amp1
Right
Tube1 Low Cut
Thru, 21...8.00k
[Hz]
a
53...20.00k,
High Cut [Hz]
Thru
Tube1 Gain
–24.0...+24.0
[dB]
b
Saturation [%]
0...100
c
Tube1 Bias
0...100
Normal,
d Tube1 Phase
Wet Invert
Tube2 Low Cut
Thru, 21...8.00k
[Hz]
e
53...20.00k,
High Cut [Hz]
Thru
Tube2 Gain
–24.0...+24.0
[dB]
f
Saturation [%]
0...100
g Tube2 Bias
0...100
Tube2 Output
h
–48.0...+0.0
Level [dB]
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
Page 394
FX Amt
Invert
+
Tube Pre Amp2
–
Output Level
FX Amt
Sets the cutoff frequency for the low
cut filter of stage 1
Sets the cutoff frequency for the
high cut filter of stage 1
Sets the input gain for stage 1
Sets the input/output response for
stage 1
Sets the bias voltage for stage 1
Turns phase reversal on/off
Sets the cutoff frequency for the low
cut filter of stage 2
Sets the cutoff frequency for the
high cut filter of stage 2
Sets the input gain for stage 2
Sets the input/output response for
stage 2
Sets the bias voltage for stage 2
Sets the output level
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
Publicité
Table des Matières
