Table des Matières
Publicité
80: P4EQ - Cho/Flng
(Parametric 4-Band EQ - Chorus/Flanger)
This effect combines a mono four-band parametric equalizer
and a chorus/flanger.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Parametric 4Band EQ
+
Trim
Right
P4EQ
a
[E]Trim
0...100
[E]B1 Cutoff
20...1.00k
[Hz]
b
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B2 Cutoff
50...5.00k
[Hz]
c
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B3 Cutoff
300...10.00k
[Hz]
d
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B4 Cutoff
500...20.00k
[Hz]
e
Q
0.5...10.0
Gain [dB]
–18...+18
CHORUS/FLANGER
[F]LFO
0.02...20.00
Frequency [Hz]
f
LFO Waveform Triangle, Sine
[F]Delay Time
0.0...1350.0
[msec]
g
Depth
0...100
Feedback
–100...+100
-Wet, -
[F]Cho/Flng
1:99...Dry...99:1
Wet/Dry
, Wet
h
Src
Off...Tempo
Amt
–100...+100
[F]Output
Normal,
i
Mode
Wet Invert
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
i: Output Mode
When Wet Invert is selected, the right channel phase of the cho-
rus/flanger effect sound is inverted. This creates pseudo-stereo
effects and adds spread.
However, if a mono-input type effect is connected after this
effect, the left and right sounds may cancel each other, eliminat-
ing the chorus/flanger effects.
FX Amt
Chorus/Flanger
Chorus/Flanger
Normal
+
Output Mode
–
Wet Invert
Feedback
Cho/Flng FX Amt
FX Amt
LFO: Tri / Sine
Sets the parametric EQ input level
Sets the center frequency of Band 1
Sets the bandwidth of Band 1
Sets the gain of Band 1
Sets the center frequency of Band 2
Sets the bandwidth of Band 2
Sets the gain of Band 2
Sets the center frequency of Band 3
Sets the bandwidth of Band 3
Sets the gain of Band 3
Sets the center frequency of Band 4
Sets the bandwidth of Band 4
Sets the gain of Band 4
Sets the speed of the LFO
Selects the LFO Waveform
Sets the delay time
Sets the depth of LFO modulation
Sets the feedback amount
Sets the effect balance of the
chorus/flanger
Selects the Wet/Dry modulation
source for the chorus/flanger
Sets the Wet/Dry modulation
amount for the chorus/flanger
Selects the output mode for the
chorus/flanger
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
81: P4EQ - Phaser
(Parametric 4-Band EQ - Phaser)
This effect combines a mono four-band parametric equalizer
and a phaser.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
Parametric 4Band EQ
+
Trim
Right
P4EQ
a
[E]Trim
0...100
[E]B1 Cutoff
20...1.00k
[Hz]
b
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B2 Cutoff
50...5.00k
[Hz]
c
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B3 Cutoff
300...10.00k
[Hz]
d
Q
0.5...10.0
Gain [dB]
–18...+18
[E]B4 Cutoff
500...20.00k
[Hz]
e
Q
0.5...10.0
Gain [dB]
–18...+18
PHASER
[P]LFO
0.02...20.00
Frequency [Hz]
f
LFO Waveform Triangle, Sine
[P]Manual
0...100
g
Depth
0...100
Resonance
–100...+100
-Wet, -
[P]Phaser Wet/
1:99...Dry...99:1
Dry
, Wet
h
Src
Off...Tempo
Amt
–100...+100
[P]Output
Normal,
i
Mode
Wet Invert
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
Page 426
FX Amt
Phaser
Phaser
Normal
+
Output Mode
–
Wet Invert
Resonance
Phaser FX Amt
FX Amt
LFO: Tri / Sine
Sets the parametric EQ input level
Sets the center frequency of Band 1
Sets the bandwidth of Band 1
Sets the gain of Band 1
Sets the center frequency of Band 2
Sets the bandwidth of Band 2
Sets the gain of Band 2
Sets the center frequency of Band 3
Sets the bandwidth of Band 3
Sets the gain of Band 3
Sets the center frequency of Band 4
Sets the bandwidth of Band 4
Sets the gain of Band 4
Sets the speed of the LFO
Selects the LFO Waveform
Sets the frequency to which the
effect is applied
Sets the depth of LFO modulation
Sets the resonance amount
Sets the phaser effect balance
Selects the Wet/Dry modulation
source for the phaser
Sets the Wet/Dry modulation
amount for the phaser
Selects the phaser output mode
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
Publicité
Table des Matières
