Table des Matières
Publicité
Dry, 1:99...99:1,
Wet/Dry
Wet
i
Src
Off...Tempo
Amt
–100...+100
a: Type
a: LFO Phase [degree]
Select the type of phaser LFO and tremolo LFO for the "Type"
parameter. How the effect sound moves or rotates depends on
the type of LFO. Selecting "LFO Phase" enables you to offset the
timing of the phaser peak and control a subtle movement and
rotation of the sound.
f: Phaser Wet/Dry
i: Wet/Dry
PHASER Wet/Dry sets the balance between the phaser output
and the dry sound. OUTPUT Wet/Dry sets the balance between
the final phaser and tremolo output level and the dry sound.
49: St. Ring Modulator
(Stereo Ring Modulator)
This effect creates a metallic sound by applying the oscillators to
the input signal. Use the LFO or Dynamic Modulation to modu-
late the oscillator to create a radical modulation. Matching the
oscillator frequency with a note number will produce a ring
modulation effect in specific key ranges.
Stereo In - Stereo Out
Left
Pre LPF
Pre LPF
Right
Fixed
Fixed Frequency
Note Offset, Fine
Note No.
Note (Key Follow)
LFO
Fixed, Note
OSC Mode
(Key Follow)
a
Pre LPF
0...100
Fixed
0...12.00k
Frequency [Hz]
Src
Off...Tempo
b
–12.00k...
Amt
+12.00k
Note Offset
–48...+48
c
Note Fine
–100...+100
LFO Frequency
0.02...20.00
[Hz]
d
Src
Off...Tempo
–20.00...
Amt
+20.00
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
FX Amt
Ring Modulator
Ring Modulator
FX Amt
Sine Oscillator
Pitch
OSC Mode
Switching between specifying the
oscillator frequency and using a
note number
Sets the damping amount of the
high range input to the ring
modulator
Sets the oscillator frequency when
OSC Mode is set to Fixed
Selects the modulation source for
the oscillator frequency when OSC
Mode is set to Fixed
Sets the modulation amount of the
oscillator frequency when OSC
Mode is set to Fixed
Sets the pitch difference from the
original note when OSC Mode is set to
Note (Key Follow)
Fine-adjusts the oscillator frequency
Sets the speed of the LFO
Selects a modulation source for LFO
speed
Sets the modulation amount of LFO
speed
MIDI Sync
Off, On
MIDI,
BPM
40.00...
e
300.00
Base Note
r...w
Times
x1...x32
LFO Depth
0...100
f
Src
Off...Tempo
Amt
–100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
g
Src
Off...Tempo
Amt
–100...+100
a: OSC Mode
This parameter determines whether or not the oscillator fre-
quency follows the note number.
a: Pre LPF
This parameter enables you to set the damping amount of the
high range sound input to the ring modulator. If the input sound
contains lots of harmonics, the effect may sound dirty. In this
case, cut a certain amount of high range.
b: Fixed Frequency [Hz]
This parameter sets the oscillator frequency when "OSC Mode"
is set to Fixed.
c: Note Offset
c: Note Fine
These parameters for the oscillator are used when "OSC Mode"
is set to Note (Key Follow). The "Note Offset" sets the pitch dif-
ference from the original note in semitone steps. The "Note
Fine" parameter fine-adjusts the pitch in cent steps. Matching
the oscillator frequency with the note number produces a ring
modulation effect in the correct key.
Page 409
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Selects the type of notes that
specify the LFO speed
Sets the number of notes that
specify the LFO speed
Sets the depth of LFO modulation
for the oscillator frequency
Selects the modulation source of
the depth of modulation
Sets the modulation amount of the
depth of modulation
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 357
Amount of modulation source
Publicité
Table des Matières
