Publicité
4. Empty any water remaining in the delivery hose so that the air can
escape during filling and priming.
5. Open any shut-off devices in the delivery line (watering accesso-
ries, tap, etc.) so that air can escape before the priming procedure
begins.
6. With fixed installation: If the delivery line cannot be emptied due to
fixed installation, unscrew the cover
liquid may escape. Please keep a sufficiently large receptacle at hand
for collection.
7. Tighten the lid
of the filter chamber up to the stopper
9
8. Without fixed installation: Lift up the delivery hose just behind the
pressure outlet.
9. Plug the power plug of the connecting cable into a mains socket.
10. Push the on / off switch
q
The on / off switch lights up.
During initial operation, the display language must be selected
after the pump is switched on.
11.
12.
13.
The pump turns off automatically approx. 10 seconds after closing
the shut-off device.
Electronic control:
The pump features an electronic controller.
If the pressure level falls below the start-up pressure, the pump is started
automatically.
As soon as the water supply is no longer required, the pump is switched
off automatically.
Low quantity programme and leakage warning:
Leakage warning:
In the event of a leakage or a dripping tap, the pressure constantly falls
below the turn-on pressure and the pump switches itself on and off con-
tinuously.
If the pump is constantly switched on and off, the pump switches off auto-
matically to prevent unwanted water leakage (error 4 "Leakage warning"
is displayed).
Low quantity programme
To prevent the pump from switching off earlier when used with low quan-
tity of water (e.g. washing machines or drip irrigation), the duration of the
low quantity programme until the leakage warning is activated can be set
(see 4. MENU SETTINGS / Leakage warning).
Switching the pump on and off cyclically during the small quantity
program has no effect on the service life of the pump.
12
GAR_01759-20.960.11_2024-01-30.indd 12
GAR_01759-20.960.11_2024-01-30.indd 12
. Considerable amounts of
r
.
<
to position I.
Select the desired display language
with the left or right button and
confirm with the centre button
The display shows "Start pump
now?".
Push the left button
.
The pump starts after approx.
2 seconds. The display shows
"Suction in progress" and the
GARDENA sun is rotating in the
display during the suction process.
The suction process can take up
to 6 min. If no water is pumped
afterwards, the Automatic Home &
Garden Pump switches off and
the display shows „ERROR 2"
(see 7. TROUBLESHOOTING").
Close shut-off devices in the delivery
pipeline again when the pump begins
to deliver water continuously.
The display shows "Flow" and
"Pressure".
The pump is ready for operation
and the display shows "Standby".
Use of washing machines
(Leakage warning set to 60 min.):
Upon completion of the low quantity water supply cycle in washing
machines, the 60-minute operating interval of the low quantity pro-
gramme is automatically reset to normal operation of the pump and
allows a trouble-free use of the washing machine for > 60 minutes.
Use without low quantities of water
(Leakage warning set to 2 min.):
If no low quantities of water are required, the leakage warning can be
reduced to 2 minutes. This enables maximum protection in the event of
a leakage.
For continuous drip irrigation
(Leakage warning set to OFF):
If the low quantity programme is to be used for more than 60 minutes,
the leakage warning can be deactivated (OFF).
Caution! The pump is then no longer protected by the leakage
warning.
4. MENU SETTINGS
.
General operation:
MENU
Left button
Centre button
Right button
Display screens during operation:
Updated information on the ope-
rating conditions can be shown
depending on the display, and vari-
ous settings can be undertaken.
ß
I
The display consists of a display
ß
II
area
and a toolbar
, which
ß
I
ß
II
states the respective functions of
the 3 buttons below e. g.:
Scroll menu upwards to "Leakage warning" .
Call up the "Turn on pressure" menu.
Scroll menu down to "Troubleshooting" .
The suction is in progress
The GARDENA sun is rotating in the display
during the suction process.
The pump delivers water
The display shows the current "Flow" and
the current "Pressure" during operation.
The pump is ready for operation
The display shows "Standby".
Delivery capacities ("Volume Counter")
v Press the right button while the pump
is delivering water or is ready for ope-
ration.
The display shows the total delivery capa-
city "Total Volume Counter" (since
the initial operation) and the partial delivery
capacity "Temp. Volume Counter"
(since the last reset) for approx. 5 seconds.
Frost warning
(The pump is out of operation)
The temperature in the pump was or is
below 4 °C.
v Push the right button and then the
centre button.
The pump is ready for operation again and
the display shows "Standby".
30.01.24 12:26
30.01.24 12:26
Publicité
