Scheppach PLM1800 Traduction Des Instructions D'origine page 31

• Brake
Switch on the machine at the start of work and allow
the machine to reach speed. Now switch the ma-
chine off again. The engine must come to a stand-
still within 10 seconds. Otherwise, there is a defect.
• Anti-kick claws
at least once per shift by a visual inspection to
establish that they are in good working order, for
example, that the contact surface has not been
damaged by impacts and that the anti-kick claws fall
back without hindrance due to their own weight;
• Planing blades
for signs of damage and to ensure they are posi-
tioned correctly.
The machine may only be used if all these condi-
tions are satisfied.
• Use only well sharpened and maintained blades.
Use only blades that are designed for the machine.
• Use pusher wood or sticks which are in perfect con-
dition for machining short workpieces.
• Connect the machine to a dust and chip extractor.
• Check that the stop is secure before starting the
machining work.
• Ensure that you can maintain your balance at all
times. Stand to the side of the machine.
• Whilst the machine is running keep your hands at
a safe distance from the cutting block and from the
point at which the chips are discharged.
• Do not start the planing work until the cutting block
has reached the required speed.
• Also ensure that the workpiece does not contain
any cables, wires, cords or the like. Do not machine
any wood which has lots of knots or knot holes.
• Secure long workpieces to prevent them tipping
over at the end of the planing process. Use roller
stands, for example, or similar devices for this pur-
pose.
• Removing sawdust and chippings from the machine
when running is strictly prohibited.
• Switch off the machine immediately it is jams. Pull
out the mains plug and remove the jammed work-
piece.
• Set the smallest cutting size after use to prevent the
risk of injury.
m CAUTION!
The machine must be secured to the floor / countertop
using suitable screws / screw clamps since otherwise
there is a risk that it will tip over.
• Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
m WARNING! Before cleaning~, adjustment~, main-
tenance~ or repair work, disconnect the power cord
from the main power supply!
• Check at regular intervals that the knife is firmly at-
tached in the knife block.
• The knives must not project more than a maximum
of 1 mm out of the knife block.
• Make sure that the anti-kick claws work correctly.
• Always wear eye protection.
• Never cut concavities, tenons or shapes.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the planing knife to run freely.
9. Installation
9.1 Stable fastening of the planing machine
(fig. 9 + 10)
• Fasten the machine to a solid surface using 4
screws.
• Mounting holes Ø 10 mm (11) for this purpose can
be found on the machine base (10) on all 4 sides.
The spacing for the mounting can be found at fig. 9.
9.2 Feed (12) and discharge table (6) (fig. 3)
• The feed (12) and discharge table (6) is pre-mounted
and is folded upwards when packaged.
• Fold down the feed (12) and discharge table (6).
9.3 Installing the height adjustment crank (4)
(fig. 4)
• First remove the cover cap for the crank (3) from
height adjustment crank (4).
• Place the height adjustment crank (4) in the crank
receptacle (26).
• Then fix the crank in place using the hexagon socket
screw (24) and washer (23). Tighten it using the Al-
len key (22) in a clockwise direction. Counterhold at
the height adjustment crank while doing this.
• Then re-affix the cover cap for the crank (3) to the
height adjustment crank (4).
www.scheppach.com GB | 31