Husqvarna 33 Manuel D'utilisation page 3

WARNING!:KICKBACK
May Occur When The
Nose Or Tip Of The Guide Bar Touches An Object,
OrWhen The Wood Closes InAnd Pinches The Saw
Chain In The Cut. Tip
Contact
In Some Cases May
Cause A Lightning Fast Reverse
REACTION,
Kicking The Guide Bar Up And Back TowardsThe
Operator.PinchingThe Saw ChainAlong The
TopOf The GuideBar May
Push The Guide Bar
Rapidly
Back Towards The Operator. Either Of
These Reactions May Cause You To Lose Control
Of The Saw
Which Could Result In Serious
Personal I njury.
Do not rely exclusively upon the safety
devicesbuilt intoyoursaw.
As a chain saw user,
you
should
take several steps to keep your cutting
jobs free from accident or injury.
(1)With a basic understanding of kickback, you can
reduce or eliminate the element of surprise.
Sudden surprise contributes to accidents.
(2) Keepa good firm grip on the saw with both
hands, the right hand on the rear handle, and the
left hand on ~hefront handle, when the engine is
running. Use a firm grip with thumbs and fingers
encircling the chain saw handles. A firm grip will
help you reduce kickback and maintain control
of the saw. Don't let go.
(3) Make sure that the area in which you are cutting
is free from obstructions. Do not let the nose of
the guide bar contact a log, branch, or any other
obstruction which could be hit while you are
operating the saw.
(4) Cut at high engine speeds.
(5) Do not overreach or cut above shoulder height.
(6) Follow manufacturer's sharpening and
maintenance instructions for the saw chain.
(7) Only use replacement bars and chains specified
by the manufacturer or the equivalent.
D 2. Other Safety Precautions
(1) Do not operate a chain saw when you are
fatigued.
(2) Use safety footwear; snug-fitting clothing;
protectivegloves; and eye, hearing, and head
protection devices.
(3) Use caution when handling fuel. Move the chain
saw at least 10feet (3 m) from the fueling point
before starting the engine.
(4) Do not allow other persons to be near the chain
saw when starting or cutting with the chain saw.
Keep bystanders and animals out of the work
area.
(5)
(6)
(7)
(8)
(9)
Do not start cutting until you have a clear work
area, secure footing, and a planned retreat path
from the falling tree.
Keepall parts of your body away from the saw
chain when the engine is running.
Before you start the engine, make sure that the
saw chain is not contacting anything.
Carry the chain saw with the engine stopped, the
guide bar and saw chain to the rear,and the
muffler awayfrom your body.
Do not operate a chain saw that is damaged,
improperly adjusted, or not completely and
securely assembled. Be sure that the saw chain
stops moving when the throttle control trigger is
released.
(10)Shut off the engine before setting the chain saw
down.
(11)Use extreme caution when cutting small size
brush and saplings because slender material
may catch the saw chain and be whipped toward
you or pull you off balance.
(12)When cuttting a limb that is under tension be
alert for springback so that you will not be struck
when the tension in the wood fibers is released.
(13)Keepthe handles dry, clean, and free of oil or
fuel mixture.
(14)Operate the chain saw only in well-ventilated
areas.
(15)Do not operate a chain saw in a tree unless you
have been specifically trained to do so.
(16)Do not operate a chain saw above shoulder
height.
(17)All chain saw service, other than the items
listed in the operator's/owner's safety and
maintenance instructions, should be performed
by competent chain saw service personnel.
(For example, if improper tools are used to
remove the flywheel or if an improper tool is
used to hold the flywheel in order to remove
the clutch, structural damage to the flywheel
could occur and subsequently cause the
flywheel to burst.)
(18)When transporting your chain saw, use the
appropriate guide bar scabbard.
Note:
This Appendix is intended primarily for the
consumer or occasional user. When using a chain
saw for logging purposes, referto the Code of Federal
Regulations, Section 1910.266(5);2.5.1.of American
National Standard SafetyRequirements for Pulpwood
Logging, ANSI 03.1-1978:and relevant state safety
codes.
@ Thefollowingtexf ismquimdbytheUS~"~~*~,~,~*.
(ANSI B 175.1-1985 Appendix D)
Safety Precaution for Chain Saw Users
D 1. Kickback Safety Precautions
Forfurthersafetyprecautions andbasiccuttingoperations see:Operator's SafetyManual.
———
3