GRAUPNER XS-6 FM RACE Instructions D'utilisation page 47

EPA Servo End-point Adjustment (Set-up Menu)
Display after switching transmitter on
C54
C54
on transmitter
TRIM RATE
I II0,6
EXP
10,6 v
V
operating voltage
Press the MODE button to reach Set-up Mode. Press the
MODE button repeatedly to select the EPA menu for servo
end-point adjustment.
End-point adjustment displays
EPA end-point steering servo left
0 to 125 "CLEAR"=100
EPA
TRIM RATE
STX
EXP
EPA
to left L/F (steering left) and
I00
adjust servo end-point using
%
L/F
L/F
INC+ or DEC-.
EPA end-point steering servo right
0 to 125 "CLEAR"=100
TRIM RATE
STX EPA
EXP
EPA
to right R/B (steering right) and
I00
% adjust servo end-point using
L/F
INC+ or DEC-.
RR/B/
EPA end-point throttle servo forward
0 to 125 "CLEAR"=100
TH EPA
TRIM RATE
EPA
lever back (forward) and adjust
servo end-point using INC+ or
I00
L/F
L/F
DEC-.
R/B
EPA end-point of break servo
0 to 125 "CLEAR"=100
EPA
TRIM RATE
TH
EPA
lever back (forward) and adjust
I00
servo end-point using INC+ or
L/F
DEC-.
R/B
R/B
EPA end-point servo 3 left
0 to 125 "CLEAR"=100
EPA
left end-point using the "A"/"C"
AUX
EPA
button and/or the mixer function
I00
L/F
"MIX" and adjust servo end-point
using INC+ or DEC-.
EPA end-point servo 3 right
0 to 125 "CLEAR"=100
EPA
right end-point using the "A"/"C"
AUX
EPA
button and/or the mixer function
I00
"MIX" and adjust servo end-point
R/B
using INC+ or DEC-.
All manuals and user guides at all-guides.com
Frequency channel set
Transmitter battery
ST
Rotate steering wheel
ST
Rotate steering wheel
TRIM RATE
EXP
REV . NORM
%
V
TH
Pull throttle/brake
TRIM RATE
EXP EP M
L/F
%
V
TH
Pull throttle/brake
REV . NORM
L/F
%
R/B
TRIM RATE V
EXP EP MI
AUX
Move servo 3 to
AUX
Move servo 3 to
The menu point EPA servo End-point Adjustment enables
you to increase or reduce maximum servo travel
separately for each servo, and for each direction from
centre. Available for steering, throttle/brake and function
3.
End-point adjustment enables you to adjust servo travel
to meet the requirements of the model.
The adjustment range is from 0% to 125%. The factory
default setting is 100% for both directions.
The direction of adjustment displayed on the screen is
reversed by moving the associated transmitter control
(steering wheel, throttle/brake lever, function 3) in the
opposite direction.
Accessing the Servo End-point Adjustment
menu
1. Switch the transmitter on to reach the Function Menu.
2. Press the MODE button repeatedly until the screen
shows the servo travel End-point Adjustment menu
EPA.
3. Use the CHANNEL button to select the function you
wish to adjust: ST (Steering), steering wheel/steering;
TH (Throttle) throttle/brake lever, or AUX (Aux.
channel) 3rd servo function.
4. Move the associated transmitter control in the direction
you wish to adjust (left/right, forward/back or brake),
then set the appropriate servo end-point using the
INC+ or DEC- buttons. Move the transmitter control
in the opposite direction, then adjust the opposite end
of the servo's travel.
5. Switch the transmitter OFF/ON briefly to store the set
values and quit the EPA (servo travel End-point
Adjustment menu). The transmitter reverts to the base
screen display.
Note: Although it is possible to set different travels for
the steering servo to either side of centre, we recommend
that you set identical travels (same left as right) if possible,
otherwise the car will exhibit different turning
characteristics to either side.
47