Publicité
Adding water
Before each cleaning operation, fi ll the solution tank with the right amount
of water and detergent opening the cap 1 or using the pipe 2. The tank is in
polyethylene and is resistant to acids, bases and most solvents.
!
Caution!
The fi lling of the clean water (solution) tank must be carried out when
both tanks are fi xed on the machine.
Choosing the detergent
For good cleaning results the correct detergent must be used. If necessary, re-
quest advice from the supplier or a competent person, remembering that an
excessively aggressive detergent may shorten the machine's working life and
fl oor. A reduced foam detergent, or an anti-foam additive, must be used to avoid
damage to the suction motor. If it is not possible to obtain these products, ordi-
nary wine vinegar can be used, pouring 50 cc. into the recovery tank before wa-
shing. After using these detergents, wash your hands and refer to the instructions
provided on the information sheet of the detergent itself.
Washing procedure
To carry out the washing procedure, proceed as follows:
•
Start brush rotation and lowering by pushing the button 3 marked with
the brush symbol.
•
Turn on the water (solution) tap, by the lever 4 and rod 5.
In order to set the cleaning water fl ow-rate in INTERMEDIATE position, set the rod
5 on position "B" and lock it by its lever 4 on position "A"-ON" (see picture), so that
the whole surface immediately behind the brushes is thoroughly wet, but there
is no excess of splashes, spills or overfl ows from the squeegee.
N.B. the amount of solution varies depending on the level in the tank.
•
Start the vacuum system by pushing the button 6, and lower the squee-
gee by its lever (see fi g.3 pos.8).
•
Select the working speed, turning the switch 7 to the "tortoise" symbol
provides low speed and thorough cleaning, the "hare" setting gives a
high speed for travelling between jobs and the position between the
"tortoise and hare" symbols gives an intermediate speed and level of
cleaning.
•
Push on the levers 8 to start the washing operation with the driving spe-
ed selected.
When the washing and drying operation is complete, proceed as follows:
•
Turn off the water by means of the lever 4 in position "A-OFF", move the
rod 5 to fully back down position "C-OFF" (see picture).
•
Stop brush rotation by pushing the button 3, lift up the brushes by pedal
11 (fi g.3).
•
Release the levers 8 to stop the travel of the scrubber .
•
Stop vacuum system by pushing the button 6 and raise the squeefrom
the fl oor by its lever.
Draining water (recovery tank)
After washing, drain the dirty water from the recovery tank using the hose 9.
Cleaning of the recovery tank
Clean accurately the recovery tank every time the washing-work is fi nished or in
case if machine is not used frequently.
!
Danger!
Do not use corrosive products to do not damage the tank and the own
health. It is necessary to use gloves and protection glasses.
Operate as described below:
•
Turn the knobs 10.
•
Remove cover 11 , fi lter 12, cup 13 and clean it.
•
Use a water jet to clean inside the recovery tank
•
When the cleaning procedure is fi nished, mount fi lter and cup.
•
Mount the cover and lock it by its knobs.
Draining water (solution tank)
Drain water when the machine is not used frequently. To drain water, open the
tap 14.
Clean water fi lter (solution tank)
•
Close water tap by the lever 4 and rod 5.
•
Remove cover and clean fi lter 15 by a water jet.
WASHING
1
3
7
49
2
6
4
MAX.
"B"
ECO
MIN.
"C"
A
A
OFF
OFF
ON
10 11
8
9
12
12
14 15
FIG.4/B
8
5
10
13
Publicité
