Publicité
Les langues disponibles
Les langues disponibles
rounding the oil filling hole. Please
adhere to the motor manufacturer's
instructions. (The original instruc-
tion manual is included.)
Check the motor oil level each time
before you start work.
Normal (2 star) petrol is recom-
mended for use.
Warning! Petrol is extreme-
A
ly flammable. Only store
petrol in containers intended for
this purpose. Only pour petrol into
the tank when outdoors and do not
smoke while filling the tank. Fill the
tank before starting the engine.
Do not open the fuel cap or pour in
petrol when the engine is running
or when the lawnmower is hot.
If petrol overflows from the tank,
do not attempt to start the engine.
Instead, move the lawnmower
away from the area where you
spilt the petrol. Do not attempt to
start the engine until the petrol
vapours have evaporated. If you
need to empty the fuel tank, this
must be done outdoors. For safety
Use
cultivated lawn, no stones, soft ground
stony uncultivated ground
uncultivated areas with a high moss content
7.3 Starting
Start or activate the start-up switch
with care and in accordance with
the manufacturer's instructions.
Ensure that there is sufficient clear-
ance between your foot and the
cutting toll. Position the aerator on
a level part of the lawn.
Inspect the grounds on which the
implement is to be used and
remove all objects which could
become caught and hurled away
from the implement.
If a foreign object blocks the cutting
tool or if the engine is overloaded,
All manuals and user guides at all-guides.com
reasons, always install a new fuel
cap and other tank caps if they
are damaged.
To prevent injury due to burns keep
the engine/exhaust and the area
around the fuel tank free of grass,
leaves and escaping grease (oil).
7.2 Adjusting the working depth
Warning! Only adjust
A
the working depth when
the engine is switched off.
Warning! The working
A
depth is pre-adjusted by
Brill and should only be readjusted
with care as a too deep insertion
into the ground can result in the
implement being subjected to over-
loading. The correct aerating depth
is < 3 mm.
The working depth must be
adjusted in accordance with
the corresponding grass and
ground situation.
Working Depth
adjust to ground level
adjust to ground level,
adjust to a lower working depth in case of stone impact
commence with a low working depth
release the safety handle and the
engine will switch off automatically.
Remove the foreign object if neces-
sary.
Warning! The aerator is not
A
to be tilted when switching
the engine on, the exception being
if the aerator needs to be lifted
during the process. In this case, tilt
it only as far as absolutely neces-
sary and only lift up the side which
is facing the user.
Before starting, switch the control
lever (fig. B pos. 3) to P (Park).
The working depth can be continu-
ously adjusted with the adjusting
hand wheel (fig. C pos. 7). The
adjusted working depth depends
on the blade wear and can be
read out from the display (fig. C).
In order to do so, the implement is
to be switched off and the control
lever (fig.B pos. 3) set to Position D
(Drive).
After frequent use, the working
depth can be readjusted in accor-
dance with the blade wear.
Note: Unplug the spark plug con-
nector! The setting should always
be inspected and adjusted on flat
ground, when the control lever
(fig. B pos. 3) is at position D
(fig. B), the blade points should
make slight contact with the
ground. The adjustment hand
wheel (fig. C pos. 7) can be turned
⁄
rotation in the direction + if
1
4
the lawn is cultivated and level.
Warning! Only adjust
A
the working depth when
the motor is switched off.
Briggs & Stratton
To start a cold motor, set the choke
lever (fig. B1, Pos. 15) to "Choke",
when the motor is warm set the
choke lever to "Run". Press the start
button (Fig. B1 Pos. 9) and pull the
safety hoop (Fig. B1 Pos. 6) in the
direction of the guide bar. With the
other hand, release the start button
and pull the starter handle (Fig. B1,
Pos. 11) to start the motor. Hold
the safety hoop against the guide
bar. After the motor has started up
and is running correctly, set the
choke lever to "Run".
GB
17
Publicité
