Salicru SLC TWIN RT3 Mode D'emploi page 51

Item Description
1 UPS
Supports for installation in tower format and
2
fixing screws
3 Quick guide
4 Warranty leaflet
5 USB cable
AC power cord - IEC 10 A
6 version and BS-type for the UK versions of 0.7 kVA,
1 kVA and 1.5 kVA)
AC power cord - IEC 16A
7
version and BS type for the 2 kVA UK versions)
AC power cord - IEC 60309 13 A (BS-type only for 3 kVA
8
UK versions)
9 Output cables
10 Rack supports and fixing screws
0.7 to 1.5 kVA units.
(1)
(2) 2 and 3 kVA units.
Tab. 3. UPS packing list.
5.1.4. Battery module content.
Check that the packaging contains the following elements:
1
3
5
Fig. 12. Battery module packaging content (EBM).
Item Description
1 EBM battery module
2 Warranty leaflet
3 Battery cable with built-in RJ45
4 Rack supports and fixing screws
Metal plate for joining several modules and
5
fixing screws
Tab. 4. Battery module content list.
USER MANUAL
Quantity
1
2
1
1
1
, (Schuko-type in its standard
(1)
1
, (Schuko type in its standard
(2)
1
1
2
2
2
4
Quantity
1
1
1
2
1
Once the reception process is complete, the UPS should be
repacked until it is started up in order to protect it against
mechanical shock, dust, dirt, etc.
The unit's packaging consists of a wooden pallet, cardboard or
wooden packaging as applicable, expanded polystyrene (EPS)
corner protectors, polyethylene cover and strips, all recyclable
materials. When you need to get rid of them, you must do so in
accordance with applicable laws.
We recommend keeping the packaging for at least 1 year.
5.1.5. Storage.
The unit must be stored in a dry, well-ventilated area, protected
from rain, dust, splashes of water or chemical agents. It is advis-
able to keep each device and battery unit in its original packaging,
as it has been specifically designed to ensure maximum protection
during transportation and storage.
For devices that contain Pb-Ca batteries, the charging
times indicated in Tab. 2 of document EK266*08,
determined by the temperature to which they are exposed, must be
respected, otherwise the warranty may be invalidated.
After this period, connect the unit to the mains together with the
battery unit, if applicable, start it according to the instructions de-
scribed in this manual and charge for 12 hours.
Then shut down the device, disconnect it and store the UPS and
batteries in their original packaging, noting the new date for
recharging the batteries on a document as a record or even on the
packaging itself.
Do not store the devices where the ambient temperature exceeds
50ºC or drops below -15ºC, as this may cause degradation of the
electrical characteristics of the batteries.
5.1.6. Transport to the site.
It is recommended to transport the UPS by means of a pallet jack
or the most appropriate method considering the distance between
the two points.
If the distance is considerable, it is recommended to move the
unit in its packaging to the vicinity of the installation site and then
unpack it.
5.1.7. Siting, immobilising and considerations.
All SLC TWIN RT3 series UPS are designed to be mounted as
a tower model -vertical arrangement of the device- or rack -hori-
zontal arrangement- for installation in 19" cabinets, regardless of
whether they operate independently or as parallel systems, whether
or not they have a battery module or whether the available backup
is standard or extended (greater number of battery modules).
Follow the instructions indicated in the sections relating to either
of the two possibilities, according to the particular configuration of
your device.
SLC TWIN RT3 0.7÷3 kVA UNINTERRUPTIBLE POWER SUPPLY (UPS)
51