Fitting Instructions - R&G LP0237BK Notice De Montage

FITTING INSTRUCTIONS


To fit the R&G tail tidy, remove the seat using the key, as shown in picture 1 and disconnect the tail
light/indicator connector that is arrowed in picture 1.

Remove the two Torx bolts that secure the front of the rear mudguard, as shown in picture 2.

Remove the two Torx bolts that secure the rear of the rear mudguard in place, as shown in picture 3. Support the
mudguard whilst removing the last bolt and then the rear mudguard assembly can be taken away from the bike,
Page | 10
as shown in picture 4.

Remove the four spacers and rubber bungs from the front and rear mounts, as shown in pictures 5 & 6.

With the rear mudguard off the bike, remove the plastic cover on the underside that hides the wiring by
removing the three bolts, as shown in picture 7.

Disconnect all the wiring connectors, as shown in picture 8.

If re-using the OEM indicators, remove the bolt that mounts them and remove the indicator from the mudguard
assembly, as shown in pictures 9 & 10.

Remove the two bolts that secure the top and bottom halves of the mudguard, as shown in pictures 11 & 12.

Disconnect the final wiring connection for the tail light and remove the wiring loom from the rear mudguard, as
shown in picture 13.

Take the R&G Tail Light (item 1 – LA0003) and fit the light shroud (item 2) before fitting one length of
heatshrink (item 22) to the wiring.

Fit one male bullet connector (item 21) to the end of each wire.

Offer this assembly up to the licence plate bracket (item 3 – TB0237 Part 1), ensuring the threaded bosses on the
light fit through the two slots and the wiring fits through the central hole, before fitting the washers and nuts and
tightening in place, as shown in pictures 14 & 15.

Take the threaded spacer (item 4 – S0977 – 12mm long) and fit it to the exposed thread of the rear bolt that
secures the locking mechanism in place, as shown in pictures 16 & 17, before tightening.

Fit the licence plate bracket assembly to the underside of the rear subframe, so that the bosses on top of the
swaged spacers locate within the mounting holes on the subframe. Whilst supporting this in place, fit the two M6
x 25mm long button head bolts (item 16) with two M6 washers (item 13) through the two mounting holes from
the underside. Fit two of the larger diameter M6 washers, (item 5) and two M6 Nyloc nuts (item 6) to the
exposed thread of each bolt on to of the subframe and tighten, as shown in pictures 18 & 19.

Fit the M6 x 10mm long button head bolt (item 17) with one M6 washer (item 13) through the remaining
mounting hole and tighten into the threaded spacer, as shown in picture 20.
If fitting the rearward mounted indicator option

Take the rearward indicator bracket (item 19 – TB0203 Part 3) and fit the indicators of choice by feeding the
wiring through the larger hole on the indicator bracket and locating the indicator boss within the hole, as shown
in picture 21.

If fitting the OEM indicators, re-use the cap head bolt to secure the indicator in place, as shown in picture 21.

If fitting the R&G Mini Indicators, secure in place using the nut and use the rubber bung supplied (item 18) to
blank off the smaller hole. Fit one length of heatshrink (item 22) to the wiring.

Offer this assembly up to the underside of the licence plate bracket already fitted, ensuring the cut-out in the
centre aligns with the slot on the licence plate bracket, before fitting two M6 x 6mm long button head bolts (item
15) with two M6 washers (item 13) through the two mounting holes on the indicator bracket and tighten into the
threaded holes on the licence plate bracket, as shown in picture 22.

Neatly route the wiring, as shown in picture 23.

Remove the two bolts that secure the plastic cover in place in front of the rear wheel, as shown in picture 24.

Take the underseat cover (item 7 – TB0237 Part 2) and offer up to the underside of the rear subframe, re-using
the OEM bolt and top hat spacer in the same way that it was removed, before loosely tightening, as shown in
picture 25.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G
www.rg-racing.com Email: info@rg-racing.com