R&G LP0237BK Notice De Montage page 12

head bolts and washers through the two mounting holes on the indicator bracket from underneath, ensuring to fit
the large diameter M6 washer (item 5) over the exposed thread of the right side bolt only, as shown in picture 35.

Offer this assembly up to the underside of the underseat cover and re-fit the washers and nyloc nuts to the bolts,
before re-tightening and securing in place, as shown in picture 36.

Neatly route the wiring around the side of the underseat cover (there is a small cut-out to position the wiring)
and use the cable ties/cable clips supplied to neatly route the wiring if required, as shown in picture 37.

Fully tighten the six bolts that secure the underseat cover in place.
Page | 12

Ensure the rubber bungs are fitted into the small holes on the indicator bracket if using mini indicators, as shown
in picture 38.

Connect the tail light/indicator loom that was removed from the mudguard assembly previously to the OEM
wiring loom at the black connector, before fitting the tail light connector (item 25 – CON0043) to the white
connector and then connect the tail light bullet connectors up as follows

If re-using the OEM indicators, re-connect these the same way that they were removed.

If using mini indicators, use the two indicator connectors (item 26 – CON0046) to connect the indicators to the
OEM loom.

If fitting R&G Aero Indicators with LED's, the yellow wire on the Aero Indicators connects with the green/red
(left indicator) or green/red (right indicator) wire on the OEM loom and the black wire on the Aero Indicators
connects with the black wire on the loom. 1x set of RGR0001 resistors (available separately) are required to
achieve the correct flash rate.

If fitting R&G Mini Indicators with bulbs, the black/white wire on the Mini Indicators connects with the
green/red (left indicator) or green/red (right indicator) wire on the OEM loom and the black wire on the Mini
Indicators connects with the black wire on the loom. No resistors are required.

If fitting R&G Mini Indicators with LED's, the black/white wire on the Mini Indicators connects with the
green/red (left indicator) or green/red (right indicator) wire on the OEM loom and the black wire on the Mini
Indicators connects with the black wire on the loom. 1x set of RGR0001 resistors (available separately) are
required to achieve the correct flash rate.

Check for the correct operation of all lights at this stage.

Tuck the wiring neatly to one side using cable ties/cable clips.

Ensure the tail tidy is correctly fitted and secured in place before re-fitting the seat unit,

Re-fit the licence plate (it may require drilling).

Depending on local laws, attach enclosed reflector in an appropriate location.

Test the licence plate illuminator and all lights before riding.
Digital copies of these instructions are available to download from
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G
shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or
maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
OEM GREEN/PURPLE ---------------------- LA0003 RED
OEM YELLOW ------------------------------- LA0003 YELLOW
OEM BLACK ---------------------------------- LA0003 BLACK
ISSUE 1 16/11/2017 (HB)
CONSUMER NOTICE
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
R&G
www.rg-racing.com Email:
as shown in picture 40.
www.rg-racing.com
info@rg-racing.com