Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
SECTION 7
USER SERVICING INSTRUCTIONS (MAINTENANCE)
SECTION 7
SECTION 7 – USER SERVICING INSTRUCTIONS (MAINTENANCE)
SECTION 7
7-1. Routine Maintenance
7-1.
Routine Maintenance
7-1. Routine Maintenance
7-1. Routine Maintenance
Disconnect power before maintaining.
!
Disconnect Power before maintaining.
!
Disconnect Power before maintaining.
�
Service equipment more often if used in severe conditions.
Service equipment more often if used in severe conditions.
!
Disconnect Power before maintaining.
Service equipment more often if used in severe conditions.
�
Service equipment more often if used in severe conditions.
Use a vacuum equipped with a HEPA filter to clean inside unit.
= Check
= Change
* To be done by Factory Authorized Service Agent
= Check
� = Check
* To be done by Factory Authorized Service Agent
= Check
Daily
* To be done by Factory Authorized Service Agent
Daily
Daily
Filter Gauge
Free Movement Of
Daily
� Filter Gauge
Filter Gauge
Base Assembly
Filter Gauge
Every
Month
Every
Every
Every
Month
Month
Month
Outer Surfaces
� Outer Surfaces
Outer Surfaces
Every
Outer Surfaces
Every 3
3
Every
Months
Every
Months
3
3
Months
Months
Unreadable Labels
Inside of Extraction Arm
� Unreadable Labels
Unreadable Labels
Unreadable Labels
Every
6
Every 6
Every
Every
Months
Months
6
6
Months
Months
Inside Unit
Sealed Bearings
Inside Unit
Inside Unit
Oil Needed
� Inside Unit
*To be done by Factory Authorized Service Agent.
7-2. Overload Protection
7-2.
7-2. Overload Protection
Overload Protection
7-2. Overload Protection
1
OM-239025 Page 18
OM-239025 Page 18
OM-239025 Page 18
USER SERVICING INSTRUCTIONS (MAINTENANCE)
USER SERVICING INSTRUCTIONS (MAINTENANCE)
USER SERVICING INSTRUCTIONS (MAINTENANCE)
= Change
= Clean
= Clean
= Replace
= Change
◇ = Change
= Change
Free Movement Of
Extraction Arm Hood
� Free Movement Of Base
Base Assembly
Free Movement Of
And Joints Stay In Position
Assembly
Free Movement Of
Base Assembly
Base Assembly
Inside of Extraction Arm
�Inside of Extraction Arm
Inside of Extraction Arm
Inside of Extraction Arm
Sealed Bearings
No
No
Fume Extractor Spark
Sealed Bearings
Oil Needed
Sealed Bearings
Guard
Oil Needed
�Sealed Bearings-No Oil
Oil Needed
Needed
1
1
1
Ref. 246152-C
= Replace
= Clean
= Replace
� = Clean
= Clean
= Replace
Extraction Arm Hood
Extraction Arm Ducts
� Extraction Arm Hood
And Joints Stay In Position
Extraction Arm Hood
And Tubing
And Joints Stay In Position
Extraction Arm Hood
And Joints Stay In Position
And Joints Stay In Position
Fume Extractor Spark
Filter
No
Fume Extractor Spark
Guard
No
Fume Extractor Spark
Guard
��Fume Extractor Spark
Guard
Guard
!
Turn off unit and disconnect
input power cord.
1
Circuit Breaker CB1
CB1 protects the blower motor from
overload. If CB1 opens the blower
motor will not run.
To access CB1, reach under front
panel.
To reset CB1, reach under front pan-
el and place CB1 in the On (up) posi-
tion.
If a fuse or circuit breaker opens,
it usually indicates a more seri-
ous problem exists. Contact a
Factory
Authorized
Agent.
� = Replace
Inner
Extraction Arm Ducts
Surface Of
Surface Of
�Inner Surface Of
� Extraction Arm
And Tubing
Hood
Extraction Arm Ducts
Hood
Hood
Ducts And
Extraction Arm Ducts
And Tubing
Tubing
And Tubing
Filter
Swivel
Filter
Base
Filter
Base
Bearings
��Filter
�Swivel Base
Bearings
Bearings
!
Turn off unit and disconnect
!
Turn off unit and disconnect
input power cord.
!
Turn off unit and disconnect
input power cord.
input power cord.
1
Circuit Breaker CB1
1
Circuit Breaker CB1
1
Circuit Breaker CB1
CB1 protects the blower motor from
CB1 protects the blower motor from
Turn off power and disconnect in-
overload. If CB1 opens the blower
overload. If CB1 opens the blower
put power cord.
CB1 protects the blower motor from
motor will not run.
motor will not run.
overload. If CB1 opens the blower
1 Circuit Breaker CB1
motor will not run.
To access CB1, reach under front
To access CB1, reach under front
panel.
panel.
To access CB1, reach under front
CB1 protects the blower motor from over-
panel.
To reset CB1, reach under front pan-
load. If CB1 opens the blower motor will not
To reset CB1, reach under front pan-
el and place CB1 in the On (up) posi-
run.
el and place CB1 in the On (up) posi-
To reset CB1, reach under front pan-
tion.
tion.
el and place CB1 in the On (up) posi-
To access CB1, reach under front panel.
tion.
If a fuse or circuit breaker opens,
If a fuse or circuit breaker opens,
it usually indicates a more seri-
To reset CB1, reach under front panel and
it usually indicates a more seri-
If a fuse or circuit breaker opens,
ous problem exists. Contact a
place CB1 in the On (up) position.
ous problem exists. Contact a
it usually indicates a more seri-
Factory
Authorized
Factory
Authorized
ous problem exists. Contact a
Service
Agent.
�
If a fuse or circuit breaker opens, it usu-
Agent.
Factory
Authorized
ally indicates a more serious problem
Agent.
exists. Contact a Factory Authorized
Service Agent.
Ref. 246152-C
OM-239025 Page 21
Inner
Inner
Inner
Surface Of
Surface Of
Hood
Hood
Swivel
Swivel
Swivel
Base
Base
Bearings
Bearings
Service
Service
Service
Ref. 246152-C
OM-249336 Page 1
Ref. 246152-C
Publicité
Table des Matières
