Publicité
Les langues disponibles
Les langues disponibles
11. Operations on the memory
For erasing the parameters related to the automatism motions (times, delays, regulations) and set again the basic ones, do as follows:
1.
Take off the power supply from the control unit; then press one of the two buttons (SEL or MODE) and keep it pressed.
2.
Supply power to the control unit
3.
The flashing light turns on for some seconds and then it turns off
4.
Release the button: in this moment the factory parameters are set into the memory modules
If you release the button at the first step (when the flashing light is still turned on) then the operation is quitted and the parameters are not cancelled.
11.2 Total erasing of the memory
For erasing the parameters related to the automation motions (times, delays, regulations) and all the learned transmitters, do as follows:
1.
Take off the power supply from the control unit; then press both buttons (SEL or MODE) and keep them pressed.
2.
Supply power to the control unit.
3.
The flashing light turns on for some seconds and then it turns off
4.
Release the buttons; the memory is cancelled when the flashing light turns off. The basic parameters related to the bascule motion are set,
and all the previously memorized transmitters are cancelled from the memory module.
If you release the button at the first step (when the flashing light is still turned on) then the operation is quitted and the parameters are not cancelled.
Factory parameters
The control unit is supplied with default settings. These settings are listed here below:
1.
Total working time (slowdowns included) = 20 seconds in opening, 23 seconds in closing
2.
Slowing down time = 9 seconds in closing and opening
3.
Courtesy light time = 1 minute
4.
Pre-flashing time (if connected) = 2 seconds
5.
Automatic reclosing time (if connected) = 10 seconds
6.
Torque adjuster time: adjusted by trimmer from 70 % up to 100 %
7.
Selection of the reception type: Rolling code
The functions can be changed by operating the 10 ways Dip Switches. The working times of the automatism can be changed in all his running phases
by pressing the SEL and MODE buttons which are located next to the 10 ways Dip Switches. These times can be changed also at a distance by using
a 4 buttons transmitter with all 4 buttons memorized into the memory module.
12. Additional devices and accessories
12.1 Fix edge function
If the fix edge are operated during a closing or an opening, then this causes a short inversion of the automation motion for approximately 2 seconds
and then its stop. If you want to use this function, then connect the fix edge at the input marked with fix edge (see drawing at page 2), otherwise this
input must be short circuited to the common.
12.2 Flashing light output
The control board is equipped with a flashing light circuit; for this reason you can externally connect only one flashing light with a fix light (FIX mod-
el) with a bulb whose power do not exceed 60 W and 230 V.
12.3 Input signaling led
The control unit is equipped with a LED signal indicating the status of the inputs in order to simplify the installation and the tests in case of fault to the
installation. The meaning of the leds is shown in the following picture, where the term "normally turned on" means that the led must be turned on when
the related input is circuited (NC input).
6-1622158 REV.03
25/09/2020
11.1 Erasing the working times
S.S.
PHOTO
STOP
EDGE
L.S.CL.
L.S.OP.
PED.
ITA
ENG
FRA
S.S. = Step by step (normally turned off)
PHOTO = Photocells (normally turned on)
STOP = Stop (normally turned on)
EDGE = Fix Edge (normally turned on)
L.S.CL. = Closing limit switch (normally turned on)
L.S.OP. = Opening limit switch (normally turned on)
PED. = Pedestrian (normally turned off)
ESP
DEU
POR
12 / 16
Publicité
