Service, Maintenance, Repair; Application And Operation - steute ES 98 SR Extreme Instructions De Montage Et De Câblage

ES 98 SR Extreme
//
Montage- und Anschlussanleitung / Bandschieflaufschalter
Mounting and wiring instructions / Belt alignment switch
Instructions de montage et de câblage / Interrupteur de déport de bande
Istruzioni di montaggio e collegamento / Interruttore di allineamento nastro
Instruções de montagem e instalação / Chave de desalinhamento
Инструкция по монтажу и подключению / Выключатель перекоса движения ленты
English
=
DANGER
Untight if mounted at low temperatures. Electric
shock hazard! Mount carefully at low temperatures.
NOTICE
Incorrect installation causes leakage. Danger of
malfunction. Only operate with an actuator. Use fit-
ting cable gland only. Observe tightening torque of
cover and actuator.
Install the belt alignment switch at both sides of the conveyor belt
close to the deflection and drive pulleys. In the case of very long con-
veyor systems, install additional belt alignment switches.
Only authorized personnel are allowed to carry out mounting, electri-
cal connection and start-up.

Application and operation

=
DANGER
Live parts. Electric shock hazard! Protective cover
over contacts must be intact.
=
DANGER
In case of overloaded contacts too high operation
temperatures. Risk of burns! For short-circuit
protection use appropriate fuse size (see
technical data).
CAUTION
High temperatures. Risk of burns! Observe permit-
ted ambient temperature.
- Use device only within the permitted electrical load limits (see
technical data).
N.B.
Do not use the device as a mechanical endstop. Any mounting posi-
tion is possible. Reconstruction and alterations to the device are not
allowed. The described products were developed in order to assume
safety functions as part of an entire plant or machine. A complete
safety system normally covers sensors, monitoring modules, indicator
switches and concepts for safe disconnection. Therefore, a validation
according to EN ISO 13849-2 or EN 62061 is necessary. Furthermore,
the Performance Level according to EN ISO 13849-1 and SIL CL Level
according to EN 62061 can be lower than the single level because of
the combination of several safety components and other safety-relat-
ed devices, e.g. by serial connection of sensors. It is the responsibility
of the manufacturer of a plant or machine to guarantee the correct
general function. Subject to technical modifications. steute does not
assume any liability for recommendations made or implied by this
description. New claims for guarantee, warranty or liability cannot be
derived from this document beyond the general terms and conditions
of delivery.

Service, maintenance, repair

=
DANGER
Live parts. Electric shock hazard! Do not repair de-
fective or damaged devices. Replace them. Excep-
tion: Use steute's original spare parts only to repair
the device. Do not rebuild or modify the device in
any way.
With rough conditions, we recommend routine maintenance as follows:
1. Check actuator for easy operation.
2. Removal of dirt.
3. Check sealing of the cable or conduit connections.
Cleaning
=
DANGER
Live parts. Electric shock hazard! Observe degree
of protection.
- In case of damp cleaning: use water or mild, non-scratching,
non-chafing cleaners.
- Do not use aggressive cleaners or solvents.
- Do not use compressed air to clean.
Disposal
- Observe national, local and legal regulations concerning disposal.
- Recycle each material separately.
Français
Utilisation des instructions de montage et de câblage
Groupe cible: personnel autorisé et compétent.
Toutes les manipulations décrites dans cette notice d'installation ne
doivent être effectuées que par du personnel formé et autorisé par la
société exploitante.
1. Lire et comprendre les instructions de montage et de câblage.
2. Respecter les règles de sécurité et de prévention des accidents
en vigueur.
3. Installer le dispositif et le mettre en service.
La sélection et l'installation des appareils et leurs intégrations dans
les systèmes de commande exigent une connaissance approfondie
de toutes les lois pertinentes, ainsi que des exigences normatives du
fabricant de la machine.
En cas de doute, la version allemande fait référence.
3 / 16