Your amp comes with AES activated (the mini switch is set to the right
to the On position). In this mode, the amp shuts down if it's left to idle
continuously for around 90 minutes. Any kind of input signal, even a
briefly played note, will bring the amp back on line, resetting its internal
auto shutdown clock to the 90-minute timeout period. If AES shuts the
amp down, you can wake it up by engaging the Power button. Slide the
mini switch to the right if you wish to deactivate AES and its automatic
shutdown function.
●
14
Speaker: Designed to drive speaker cabinets with impedances from
4 to 16 ohms, this speaker out lets you connect any kind of guitar speaker
cabinet, from small enclosures up to a full 4x12" stack. Yes, your AmpMan
can drive even the biggest of speakers!
Caution: If you wish to connect two speaker cabinets, always make sure
they are of the same type. NEVER mix the two by connecting one of each
type! If you want to connect two cabinets, make sure the impedance of
each cabinet is 8 ohms minimum, as the overall impedance is halved in
a parallel circuit.
The Hughes & Kettner TS 112 Pro, TM 112 and TM 212 speakers come
highly recommended. Each has an impedance of 16 ohms and a parallel
output that lets you connect a second speaker of the same type.
●
15
VDC: Input jack for the included power supply. AmpMan comes
with a universal power supply that works reliably at any mains voltage
worldwide and maintains the sound quality wherever you go. Please only
use the original power supply.
Caution: Always connect the power supply to AmpMan first, and then
connect the power supply to a wall outlet.
3 Smart Mode
AmpMan's Smart mode lets you store Boost and FX Loop settings for each
channel. For example, you could enable Boost and the FX Loop in Channel
B and disable these functions for Channel A. The amp will recall these
settings when you switch channels, so a single touch of a button lets you
switch from a dry rhythm sound in Channel A to a wet lead sound in
Channel B with Boost and the FX Loop activated. The amp ships with
Smart mode deactivated.
Activating/deactivating Smart mode: Simultaneously press and hold the
Solo and Channel A/B for three seconds – that is, the two switches at the far
left and right – to set AmpMan to Smart mode. The Channel LEDs will flash
to confirm you have activated Smart mode. AmpMan retains this setting
even after you switch the device off. The same procedure deactivates
Smart mode.
Heads up: There is no indicator to tell you Smart mode is active. If you
want to check to make sure, simply switch Boost on in Channel A and off
in Channel B. AmpMan is in Smart mode if Boost remains active when you
switch back to Channel A.
4 Technical Data
Spirit AmpMan Series
Max. power consumption
DC input
External power supply
Mains voltage tolerance range
Ambient operating temperature range
Input jack
Sensitivity (Clean, all knobs at 12 o'clock,
Master maxed)
Max. level
FX Send jack
Nominal level (Clean, all knobs at 12
o'clock, Tone knob turned down)
Max. level
FX Return jack
Sensitivity (Clean, all knobs at 12 o'clock,
Master maxed)
Max. level
Aux In mini jack
Sensitivity
Max. level
Phones mini jack
Nominal level (Clean, all knobs at 12
o'clock, Tone knob turned down, Master
maxed, Phones 70% volume)
Max. level (Clean, all knobs at 12 o'clock,
Tone knob turned down, Master maxed,
Phones 100% volume)
Max. level
Red Box AE+ Out
Nominal level (Clean, w/o Boost, all knobs
at 12 o'clock, Tone knob turned down)
Max. level
Speaker jack
Power output @ 16 ohms
Power output @ 8 ohms
Power output @ 4 ohms
Dimensions amp (W x H x D)
Weight amp
Dimensions power supply (W x H x D)
Weight power supply
All mentioned trademarks and copyrights belong to their respective owners.
Spirit™ AmpMan Series – Manual 1.2
50 W
+24 V / 2.5 A (Polarity: center = +)
100 – 240 V, 50 – 60 Hz
+/-10 %
0° to +35° C
6.3 mm (1/4"), unbalanced, 1 MOhms
–13 dBV
0 dBV
6.3 mm (1/4"), unbalanced, 220 ohms
–6 dBV
+10 dBV
6.3 mm (1/4"), unbalanced, 20 kOhms
–6 dBV
+9 dBV
3.5 mm stereo, 10 kOhms
–6 dBV
+26 dBV
3.5 mm stereo, 50 ohms
–6 dBV
0 dBV
+11 dBV
XLR, balanced, Line: 400 ohms, Mic: 600
ohms
Line: –6 dBV, Mic: –26 dBV
Line: +6 dBV, Mic: –14 dBV
6.3 mm (1/4"), bridged mode, 4 – 16 ohms
13 W
25 W
48 W
250 x 52 x 153 mms
1150 g
129 x 32 x 52 mms
280 g
7