Link Wiring - Lutron GRAFIK 7000 Guide D'installation Et De Maintenance

Power Panels (PPs):

Link Wiring

Wire the power panel link to all power panels as shown below. See instruction sheets provided with
each power panel for complete wiring and mounting instructions.
T1 T1 T2 T2 T3 T3 T4 T4 T5 T5 T6 T6
H H H H H H H H H H H H
N N N N N N H H H H
0 0
T1 T1 T2 T2 T3 T3 T4 T4 T5 T5 T6 T6
N N N N N N N N N N N N
I I
Terminator
Processor Panel
(GRAFIK 7000P
with 6 links shown)
Note: Label shown is on top of processor assembly.
Connectors are located on bottom surface of processor
assembly.
Notes
• It is not necessary to have the processor panel
at the end of the PP link
• The power panel link's sense wire is used
whenever there is a panel being supplied by an
emergency/essential feed; see power panel
instructions for more details
24 Installation of GRAFIK 5000/6000/7000 System
PP Link
1 2 3 4 D
3 4
Link Control Wiring
(2) #18 AWG
(LT-1) 2
(1.0 mm )
1: Common
2: Sense
1 2 3 4 D 5 C D
Data A OK Power OK Data B OK
Link Link
A B
1 2 3 4 D 5 C D
S ELECT C IRCUIT
1
2
Circuit
V IEW V ALUE
S ELECT V ALUE
Link A 3
Link B 4
Value
S ELECT V ALUE D ISPLAYED
Circuit Level 5
Load Type (See Instructions)
Zone Assignment w/ Circuit Schedule
Zone Assignment w/ Zone Capture TM
Low-End Trim
High-End Trim
Address ('Ad' displayed)
Warning - Read instructions to set the Load
Type. Instructions show more load types.
Load Type Quick Reference:
--- Unassigned 3-1 Neon / CC
1-1 Incandescent 4-1 Non-Dim
2-1 Fluorescent Lutron Hi-lume R FDB Ballast
2-2 Fluorescent Lutron Tu-Wire Ballast
TM
LINK 1 LINK 2 (Non-Ess) (Essential)
Normal Emergency
Power Panel
Power Panel
Data Link
(1) shielded, twisted pair #18 AWG (1.0 mm
3: MUX
4: MUX
D: Drain wire in shield - Keep away from
ground and all electronics
• See RS485 Wiring Overview for approved cable
options
1 2 3 4 D 5 C D
Data A OK Power OK Data B OK
Link Link
A B
1 2 3 4 D 5 C D
S ELECT C IRCUIT
1
2
Circuit
V IEW V ALUE
S V
ELECT ALUE
Link A 3
Link B 4
Value
S ELECT V ALUE D ISPLAYED
Circuit Level 5
Load Type (See Instructions)
Zone Assignment
w/ Circuit Schedule
Zone Assignment w/ Zone Capture
TM
Low-End Trim
High-End Trim
Address ('Ad' displayed)
Warning - Read instructions to set the Load
Type. Instructions show more load types.
Load Type Quick Reference:
--- Unassigned 3-1 Neon / CC
1-1 Incandescent 4-1 Non-Dim
2-1 Fluorescent Lutron Hi-lume R FDB Ballast
2-2 Fluorescent Lutron Tu-Wire TM Ballast
LINK 1 LINK 2 (Non-Ess) (Essential)
Normal Emergency
Last Power Panel
on Link
3
Link
2
)
3
Terminator
(LT-1)
Emergency /
Essential
Sense Line
(1) #18 AWG
2
(1.0 mm )
5: Sense
1 2 3 4 D 5 C D
Data A OK Power OK Data B OK
Link Link
A B
1 2 3 4 D 5 C D
S ELECT C IRCUIT
1
2
Circuit
V IEW V ALUE
S V
ELECT ALUE
Link A 3
Link B 4
Value
S ELECT V ALUE D ISPLAYED
Circuit Level 5
Load Type (See Instructions)
Zone Assignment
w/ Circuit Schedule
Zone Assignment w/ Zone Capture
TM
Low-End Trim
High-End Trim
Address ('Ad' displayed)
Warning - Read instructions to set the Load
Type. Instructions show more load types.
Load Type Quick Reference:
--- Unassigned 3-1 Neon / CC
1-1 Incandescent 4-1 Non-Dim
2-1 Fluorescent Lutron Hi-lume R FDB Ballast
2-2 Fluorescent Lutron Tu-Wire TM Ballast
LINK 1 LINK 2 (Non-Ess) (Essential)
Normal Emergency
4
4
R