Addressing - Lutron GRAFIK 7000 Guide D'installation Et De Maintenance

Processor Panels:

Addressing

If there is only one processor panel in the
system, leave its address as shipped (default
is address 1). For proper operation, the
address of the processor must match the
address set in the eLumen software.
If there are two or more processor panels in
the system, each must have a unique address
between 1 and 32. The address switches may
have been pre-set to give the address shown
on the job drawings.
Use the chart below to see how to set the
processor address switches to get a specific
processor address. Set address switches 6
and 7 to the OFF (down) position.
Notes
• Processor panels may be pre-addressed by the factory; otherwise, they must be addressed during
installation by the electrical contractor
• Processor panel address switches 1 through 5 should be set as shown below
• Set processor panel address switches 6 and 7 to the OFF (down) position
ON
1 9
1 2 3 4 5 6 7
ON
2 10
1 2 3 4 5 6 7
ON
3 11
1 2 3 4 5 6 7
ON
4 12
1 2 3 4 5 6 7
ON
5 13
1 2 3 4 5 6 7
ON
6 14
1 2 3 4 5 6 7
ON
7 15
1 2 3 4 5 6 7
ON
8 16
1 2 3 4 5 6 7
ON
17
5 6 7
1 2 3 4
ON
18
1 2 3 4 5 6 7
ON
19
1 2 3 4 5 6 7
ON
20
5 6 7
1 2 3 4
ON
21
1 2 3 4 5 6 7
ON
22
5 6 7
1 2 3 4
ON
23
1 2 3 4
5 6 7
ON
24
1 2 3 4 5 6 7
R
T1 T1 H H T2 T2 H H T3 T3 H H T4 T4 H H T5 T5 H H T6 T6 H H
0 0
T1 T1 T2 T2 T3 T3 T4 T4 T5 T5 T6 T6
N N N N N N N N N N N N
I I
GRAFIK 7000P processor panel
with 6 links shown.
ON
25
1 2 3 4 5 6 7
ON
26
1 2 3 4 5 6 7
ON
27
1 2 3 4 5 6 7
ON
28
1 2 3 4 5 6 7
ON
29
1 2 3 4 5 6 7
ON
30
1 2 3 4 5 6 7
ON
31
1 2 3 4
5 6 7
ON
32
1 2 3 4
5 6 7
Installation of GRAFIK 5000/6000/7000 System
N N N N N N H H H H
Processor panel
address switch
ON
1 2 3 4 5 6 7
(address 1 shown)
ON
5 6 7
1 2 3 4
ON
1 2 3 4 5 6 7
ON
1 2 3 4
5 6 7
ON
1 2 3 4
5 6 7
ON
1 2 3 4
5 6 7
ON
1 2 3 4
5 6 7
ON
1 2 3 4
5 6 7
ON
1 2 3 4
5 6 7
9