DAB e.sybox Instructions Pour L'installation Et L'entretien page 61

7.5.4 MS: Measuring system
7.5.5 AS: Association of devices
7.5.6 PR: Remote pressure sensor
7.6 Technical Assistance Menu
7.6.1 TB: Water lack blockage time
7.6.2 T1: Switch-off time after low pressure signal
7.6.3 T2: Delay in switching off
7.6.4 GP: Proportional gain coefficient
7.6.5 GI: Integral gain coefficient
7.6.6 RM: Maximum speed
7.6.7 Setting the number of devices and of reserves
7.6.8 NA: Active devices
7.6.9 NC: Simultaneous devices
7.6.10 IC: Configuration of the reserve
7.6.10.1 Examples of configuration for multipump systems
7.6.11 ET: Max. switching time
7.6.12 AY: Anti Cycling
7.6.13 AE: Enabling the anti-block function
7.6.14 AF: Enabling the anti-freeze function
7.6.15 Setup of the auxiliary digitali inputs IN1, IN2, IN3, IN4
7.6.15.1 Disabling the functions associated with the input
7.6.15.2 Setting external float function
7.6.15.3 Setting auxiliary setpoint input function
7.6.15.4 Setting system enabling and fault reset
7.6.15.5 Setting low pressure detection (KIWA)
7.6.16 Setup of the outputs OUT1, OUT2
7.6.17 O1: Setting output 1 function
7.6.18 O2: Setting output 2 function
7.6.19 FW: Firmware update
7.6.20 RF: Fault and warning reset
7.6.21 PW: Change password
7.6.21.1 Password for multipump systems
8. Reset and factory settings
8.1 Reset generale del sistema
8.2 Factory settings
8.3 Restoring the factory settings
9. Particular installations
9.1 Inhibiting self-priming
9.2 Wall installation
9.3 Installation with Quick Connection
9.4 Multiple Sets
9.4.1 Introduction to multipump systems
9.4.2 Making a multipump system
87 9.4.3 Wireless communication
87 9.4.4 Connection and setting of the inputs
88 9.4.5 Parameters linked to multipump operation
88 9.4.6 First start of the multipump system
88 9.4.7 Multipump adjustment
89 9.4.8 Assigning the starting order
89 9.4.9 Max. switching time
89 9.4.10 Reaching the maximum inactivity time
89 9.4.11 Reserves and number of devices that participate in pumping
89 9.4.12 Wireless Control
89
10. Maintenance
89
10.1 Accessory tool
89
10.2 Emptying the system
90
10.3 Non-return valve
90
10.4 Motor shaft
90
10.5 Expansion Vessel
91
91 11. Updating the e.Sybox firmware
91 11.1 General
91
11.2 Updating the firmware
92 11.2.1 Updating between one e.sybox and another
92
11.2.1.1 Manual updating
92 11.2.1.2 Automatic updating
93
11.2.1.3 Semiautomatic updating
94 11.2.2 Updating the e.sybox by e.sylink
94
12. Troubleshooting
95
95
13. Disposal
95
14. Guarantee
95
95
96
96
96
96
96
98
98
99
99
99
99
99
GB
ENGLISH
100
100
100
101
101
102
102
102
102
103
103
103
105
105
106
106
106
106
107
107
107
107
108
109
109
110
110
58