Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
BEFORE INSTALLATION
Parts
Check that the following parts are included in the packaging:
1
Figure 1: Sauna heater parts
1. Sauna heater
2. Bracket screws x 8
3. Bracketsx 4
4. Warning sticker in ten languages
5. Bracket screws x 4
6. Connectors x 3
7. Lock screw B8x9.5 x 1
Contact your dealer if anything is missing.
Installation requirements
To ensure safe use of the heater, check that the following criteria
are met:
•
Cable (EKK) or electrical ducting (Fk) for connecting the hea-
termust be run on the outside of the heat insulation.
•
Cable installation must be correctly performed (see The sec-
tion called Connection/wiring diagram, Page 8).
•
Fuse size (A) and power cable size (mm²) must be suitable
for the heater (see The section called Connection/wiring
diagram, Page 8.
•
The sauna ventilation must comply with the instructions in
this manual (see The section called Positioning the inlet vent,
Page 6, The section called Positioning the outlet vent, Page
6).
•
The position of the sauna heater must comply with the in-
structions in this manual.
•
The heater output (kW) must be suitable for the sauna volu-
me (m³) (see Table 1, Page 5). The minimum and maximum-
volumes must not be exceeded.
NOTE! A brick wall without heat insulation increases
the warm-up time. Each square metre of plastered
ceiling or wall surface equals an additional 1.2–2 m³
of sauna volume.
Table 1: Output and sauna volume
Output kW
6,6
8
3
2
5
4
6
7
Sauna volume min./max. m³
4-8
6-12
DANGER! Incorrect ventilation or heater positi-
oning can lead to the wooden panels drying out,
posing a fi re risk in certain circumstances.
DANGER! Insuffi cient insulation of the sauna
cabin can pose a fi re risk.
DANGER! Use of the wrong materials in the
cabin, such as chipboard, plasterboard etc., can
pose a fi re risk.
DANGER! The heater must be connected by a qua-
lifi ed electrician according to the applicable regula-
tions.
Installation tools
The following tools and materials are needed for installation and
connection:
•
spirit level,
•
adjustable spanner,
•
electric drill,
•
screwdriver.
Planning installation
Before starting to install your sauna heater:
•
Plan where to position the sauna heater (see The section
called Positioning the heater - normal installation, Page 5).
•
Position the inlet vent (see The section called Positioning the
inlet vent, Page 6).
•
Position the outlet vent (see The section called Positioning
the outlet vent, Page 6).
•
Plan the electrical installation see The section called Connec-
tion/wiring diagram, Page 8.
Positioning the heater - normal installation
DANGER! More than one heater can't be installed
in the same sauna cabin.
Position the sauna heater:
•
on the same wall as the door (or the side wall if very close
tothe door wall). The heater can also be positioned in a re-
cess (see Figure 3, Page 6).
•
at a safe distance from the fl oor, side walls and interior fi t-
tings (see Figure 2, Page 5).
1
Figure 2: Positioning the heater - normal installation
1.
Minimum distance from side wall: 110 mm
2.
Minimum distance from ceiling: 1030 mm
3.
Minimum distance from interior fi ttings: 100 mm
4.
Minimum ceiling height: 1900 mm
5.
Minimum distance: 20 mm
6.
Minimum distance from interior fi ttings: 30 mm
7.
Distance from fl oor: 270 mm
5
2
3
4
6
5
7
Publicité
Table des Matières
