ero electronic TMS Mode D'emploi page 21

I P Integral pre-load Integral pre-load Integral pre-load Integral pre-load Integral pre-load
"IP" is skipped if Pb=0 (ON/OFF action).
Ranges:
- from 0 to 100 % when P4 = H
- from -100 to 100 % when P4 = HC
C Output 1 cycle time Output 1 cycle time Output 1 cycle time
Output 1 cycle time Output 1 cycle time
C is available if Pb parameter is different
from 0 only.
Range: from 1 to 200 s.
Output 2 cycle time Output 2 cycle time
C2 Output 2 cycle time Output 2 cycle time Output 2 cycle time
C2 is available only if P4 = "HC" and Pb is
different from 0 only.
Range: from 1 to 200 s.
rC Relative Cooling gain . Relative Cooling gain . Relative Cooling gain . Relative Cooling gain . Relative Cooling gain .
"rC" is skipped if Pb=0 (ON/OFF action)
or P4 = H.
Range: from 0.20 to 1.00
Note: When SMART function is enabled, Note Note Note Note
the "rC" parameter is limited in accord-
ance to the selected coolant:
- from 0.85 to 1.00 when P6 = AIr
- from 0.80 to 0.90 when P6 = OIL
- from 0.30 to 0.60 when P6 = H2O
Dead band/Overlap between H/C Dead band/Overlap between H/C
OLP Dead band/Overlap between H/C Dead band/Overlap between H/C Dead band/Overlap between H/C
outputs outputs outputs outputs outputs
"OLP" is skipped if Pb=0 (ON/OFF action)
or P4 = H.
A negative OLAP value shows a dead
band while a positive value shows an
overlap.
Range: from -20 to 50.
rL Set point low limit Set point low limit Set point low limit Set point low limit Set point low limit
Range: from min. range value (P2) to rH.
Note: When P2 has been modified, rL will Note Note Note Note
be realigned to it.
rH Set point high limit Set point high limit Set point high limit Set point high limit Set point high limit
Range: From rL to full scale value (P3).
Note: When P3 has been modified, rH will Note Note
Note Note
be realigned to it.
rP Ramp applied to the set point changes Ramp applied to the set point changes Ramp applied to the set point changes Ramp applied to the set point changes Ramp applied to the set point changes
Range: from 1 to 100 digit/min.
Above this value the display shows "inf"
and the transfer will be a step transfer.
OLH Control output high limit Control output high limit Control output high limit Control output high limit Control output high limit
"OLH" is skipped if Pb=0 (ON/OFF action).
Range:
- from 0 to 100 % when P4 = H
- from -100 to 100 % when P4 = HC
Time duration of the output power Time duration of the output power
tOL Time duration of the output power Time duration of the output power Time duration of the output power
limiter limiter limiter limiter limiter
"tOL" is skipped if Pb=0 (ON/OFF action).
Range: from 1 to 100 min.
Above this value the display shows "inf"
and the limit will be ever enabled.
Note: The tOL can be modified but the Note Note Note Note
new value will become operative only at
the next instrument start up.
Hbd Threshold of the heater break down Threshold of the heater break down Threshold of the heater break down Threshold of the heater break down Threshold of the heater break down
alarm alarm alarm
alarm alarm
"Hbd" is available only when P16 is
different from OFF.
Range: within the current transformer
range (see P17).
GB GB GB GB GB 18