Scheppach DS920 Traduction De La Notice Originale page 21

Note: lf you want to avoid irregular grinding results, do
not keep the power tool at one spot for too long.
7. Lift the grinding plate (9) from the surface to be pro-
cessed before switching off the power tool.
8. Do not put aside the power tool until the insertion tool
has come to a complete halt.
After use
1. Switch off the power tool as described, disconnect it
from the power supply and Iet it cool down.
2. Clean and maintain the power tool as described below,
and store it carefully.
Cleaning, maintenance and repair
WARNING! Unplug the power tool before starting to
work on it (e.g. transport, installation, retrofitting,
cleaning and maintenance)!
Cleaning
a) Keep protective devices, ventilation openings and mo-
tor housings free from dust and dirt as far as possible.
b) Wipe the power tool with a clean cloth or remove dust
and dirt with compressed air at low pressure (max. 3
bar).
c) Clean the power tool immediately after each use.
d) Do not use any detergents or solvents as they may
affect the plastic parts of the power tool. Make sure to
avoid any water ingress into the tool.
Replacing the power supply line
lf the power supply line of this power tool is damaged, it
must be replaced by the manufacturer or the customer
service or any equally qualified person in order to avoid
risks.
Maintenance
Check the power tool and accessory parts (e.g. insertion
tools) for wear and darnage before and after each op-
eration. lf necessary, replace worn out or damaged parts
with new parts and make sure to comply with the oper-
ating instructions. Observe any technical requirements.
Grinding plate, brush edge
Have a qualified specialist replace damaged or worn out
grinding plates (9) and brush edges (10) with new ones
of the same type.
Replacing the power supply line
lf the power supply line ofthispower tool is damaged, it
must be replaced by the manufacturer or the customer
service or an equally qualified person in order to avoid
risks.
WARNING! There are no parts inside the power tool
which can be serviced by the operator! Never open
the power tool! Take it to a qualified specialist for
further maintenance!
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Storage and transport
1. Whenever you do not use the power tool, you must
keep it in a dry and weil ventilated place out of the
reach of children, e.g. on a high cabinet or in a closed
place.
2. Keep power tool, instruction manual and accessory
parts, if any, together in the original packaging, if pos-
sible. Thus you have all information and parts avail-
able at any time.
3. Always hold the power tool by its handle.
4. To avoid transport damages, you must pack the power
tool or use the original packaging.
5. Protect the power tool against vibrations and shock,
especially during transport in vehicles.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must not
be disposed of together with domestic waste in
compliance with the Directive (2012/19/EU) per-
taining to waste electrical and electronic equip-
ment (WEEE). This product must be disposed of at a
designated collection point. This can occur, for exam-
ple, by handing it in at an authorised collecting point for
the recycling of waste electrical and electronic equip-
ment. Improper handling of waste equipment may have
negative consequences for the environment and human
health due to potentially hazardous substances that are
often contained in electrical and electronic equipment.
By properly disposing of this product, you are also con-
tributing to the effective use of natural resources. You
can obtain information on collection points for waste
equipment from your municipal administration, public
waste disposal authority, an authorised body for the
disposal of waste electrical and electronic equipment
or your waste disposal company.
21 І 92