Scheppach DS920 Traduction De La Notice Originale page 16

Introduction
MANUFACTURER
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We wish you much joy and success in working with your
new device.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability for
damages to the product or damages caused by the prod-
uct that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advantage
of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only
be operated by persons who were instructed concern-
ing the operation of the machine and who are informed
about the associated dangers. The minimum age re-
quirement must be complied with.
16 І 92
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
lntended use
The intended use of this power tool is the sanding of
large areas of drywalls as a preparation before painting
or wallpapering using suitable abrasive sheets.
This power tool is neither suited for the preparation of
small areas, corners and edges, nor for the removal of
wallpaper and the grinding of ceilings and wet grinding.
Do not use the power tool for cutting or roughing or pol-
ishing. Do not use it together with wire brushes. Do not
treat asbestos containing materials with this power tool.
This power tool is solely intended for private use. Da
not use the power tool for any other purpose than for
the intended one. Any other use beyond the intended
use is im proper.
For any resulting darnage or injury, the user/Operator is
held liable, not the manufacturer.
Technical Data
Nominal voltage:
Nominal frequency:
Power consumption:
Nominalspeed (oscillation
rate) n:
Spindie size:
Abrasive paper diameter:
Protection class:
Weight.:
Sound level
Sound pressure Ievel L .:
PA
Sound power Ievei L .:
WA
Uncertainty K
Hand-arm vibration
When grinding with abrasive
sheets a
h
Uncertainty K:
The specified hand-arm vibration value is based on
grinding with an abrasive sheet. Different applications
may result in different values.
The noise and vibration values were determined accord-
ing to EN 60745-1 and EN 60745-2-3.
The specified vibration value was measured an the basis
of a standard test method and can be used to compare
any kind of power tools.
The specified vibration value can also be used for the
initial evaluation of exposure.
Warning! Depending on how you use the power tool,
the actual vibration values may deviate from the spec-
ified values!
Take measures to protect yourself against vibrations!
Make sure to take into account the entire work pro-
cess, i.e. also times when the power tool is operat-
ed without Ioad or switched off! Appropriate meas-
ures include the regular maintenance and care of
230-240 V~
50 Hz
710 W
700 - 1700 1/min
M14
225 mm
II
3.8 kg
78 dB(A)
89 dB(A)
3 dB(A)
2,28 m/s
2
1,5 m/s
2