Transport; Working Instructions; Cleaning And Maintenance; Storage - Scheppach 5903405901 Traduction Des Instructions D'origine

• To prevent the abrasive paper from becoming worn
on one side, the workpiece should be moved to
and from on the grindinög/sanding belt or grinding/
sanding plate as you grind/sand.
• IMPORTANT! Pieces of wood should always be
sanded with the grain to prevent them splitting. Im­
portant. If the grinding wheel or the grinding/sand­
ing belt becomes jammed during operation, please
remove the workpiece until the tool reaches its top
speed again.

8. Transport

If you want to move the equipment to a different place,
disconnect the equipment from the power supply and
set it up in the new position you want to use it in.

9. Working instructions

Bevel sanding, Fig. 14
The worktable can be tilted from 0° to 45° for bevel
sanding. To tilt the worktable:
• Loosen the fixing screw (4).
• Push the lever (15) down.
• Set worktable to desired angle.
• Retighten the fixing screw (4) again.
Surface sanding on the sanding belt
• Hold the workpiece firmly, keeping fingers away
from the sanding belt.
• Keep the end pressed firmly against the work sup­
port moving work evenly across the sanding belt.
Note: Use extra caution when sanding very thin
pieces and when sanding extra long pieces, remove
the work support. Apply only enough pressure to al­
low the sanding belt to remove the material.

10. Cleaning and maintenance

m WARNING! Prior to any adjustment, maintenance
or service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time us­
ing a cloth. In order to extend the service life of the tool, oil
the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive prod - uct.
General maintenance
After using your belt/disc sander, clean it completely
and lubricate all sliding and moving parts. Apply a
light coat of automotive type paste wax to the workta­
ble to help keep the surfaces clean.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consuma­
bles.
Wear parts*: grinding medium, Carbon brushes,
sharpening wheel, angle gauge, v­belt
* Not necessarily included in the scope of delivery!

11. Storage

Store the device and its accessories in a dark, dry and
frost­proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.

12. Electrical Connection

The installed electric motor is connected and is ready
to work.
The connection complies with the relevant VDE and
DIN regulations.
The customer-side mains supply and the used exten­
sion line must meet these regulations.
Defective Electric Connection Lines
Often, insulation damages occur on electrical con­
nection lines.
Causes are:
• Drag marks if connection lines are led through win­
dow or door clearances.
• Kinks due to improper attachment or routing of the
connection line.
• Cuts caused by running over the connection line.
• Insulation damages caused by pulling the connec­
tion line out of the wall socket.
• Fissures caused by the ageing of the insulation.
Such defective electric connection lines must not be
used and are hazardous due to the insulation dam­
ages.
Regularly check the electrical connection lines for
damages. Please make sure that the connection lines
are disconnected from the mains supply during the
check.
Electrical connection lines must comply with the rel­
evant VDE and DIN regulations. Only use connection
lines labelled with H05VV-F. The labelling of the con­
nection cable with the type specification is required.
GB | 23