Cardin BL Série Mode D'emploi page 35

CONTINUED FROM PAGE 10
In stage "A" step "1" you have selected the parameter "single motor"
YES
Note 1: Selecting a
single gate (gate1)
automatically disables
the travel limits for gate
2.
Excluding travel limits
during programming
means you will not have
to bridge the contacts
on the terminal board.
Press prog to start
a programming cycle
PRESS
with:
PROG
- Single motor -
Open gate leaf 1
Press prog before gate leaf
1 reaches the travel limit. PRESS
End calibration sensor 1
PROG
(opening direction)
When the gate reaches
the mechanical stop or
reaches the opening travel
limit the pause time count
will start.
PRESS
End pause time count
PROG
(start closing cycle )
Close gate leaf 1
Press prog before gate leaf
1 reaches the travel limit.
PRESS
End calibration sensor 1 PROG
(closing direction)
The end of programming is
indicated by the courtesy
light switching on and the
display switching off.
- Note 2 -
The maximum closing direction delay time for
gate 1 is equal to the work time of gate 2.
• If you wish to exit programming without
memorising the time elapsed press the "SEL"
button.
The gates will block and only the system
definition parameters will be memorised
including the deceleration and electrical
sensor settings.
• The intervention of the travel direction inversion or blocking photocell or pressing the block-
ing button will stop the gate, while the flashing warning light will remain lit, indicating that the
programmer is in an active phase. The figure "b" will flash on the display.
The work time count is blocked, but once the alarm situation has been resolved or the blocking
button has been released (only active while it is being pressed down) the gate movement will
start up again automatically, and the time count will carry on.
• The intervention of a mechanical travel limit or the electrical input sensor will cause the gate leaf to stop and the work cycle time to expire.
WARNING! Program the work time so that the gate always opens completely, otherwise the completion of the manoeuvre cannot be guaranteed (see
paragraph "timer travel limits").
In stage "A" step "2" you have selected the parameter "Sliding gates"
Press prog to start
a programming cycle
with:
- Two sliding gates-
Open gate leaves 1 and 2
Press prog before gate leaf
1 reaches the travel limit.
End calibration sensor 1
(opening direction)
Press prog before
gate leaf 2 reaches the
travel limit. End calibration
sensor 2 (opening direction)
When both the gates
reach the mechanical stop
or both reache the opening
travel limit the pause
time count will start.
End pause time count
(start closing cycle )
Open gate leaves 1 and 2
Press prog before gate leaf
2 reaches the travel limit.
End calibration sensor 2
(closing direction)
DS1
Press prog before gate leaf
1 reaches the travel limit.
End calibration sensor 1
(closing direction)
The end of programming is
indicated by the courtesy
light switching on and the
display switching off.
STAGE "D" PROGRAMMING THE WORK TIMES
NO
YES
PRESS
PROG
PRESS
PROG
PRESS
PROG
PRESS
PROG
PRESS
PROG
PRESS
PROG
DS1
11
Programming is carried out step by step by the system
which activates the motors according to the settings
carried out in the previous step (e.g.: If you have chosen
a 1 gate configuration, only motor number 1 will be acti-
vated). If the electric locking device, preflashing and gate
jolt (initial movement in the closing direction) have been
enabled, they must also be set during programming.
Press prog to start
a programming cycle
PRESS
with:
- Two hinged gates-
Open gate leaf 1 and after
2 seconds (out of
synchronism movement)
gate 2 will start
Press prog before gate leaf
1 reaches the travel limit.
PRESS
End calibration sensor 1
(opening direction)
Press prog before
gate leaf 2 reaches the
travel limit. End calibration
sensor 2 (opening direction)
When both the gates
reach the mechanical stop
or both reache the opening
travel limit the pause
time count will start.
End pause time count
start closing cycle gate 2
Close gate leaf 2
Close gate 1
End closing synchonism
movement - Note 2 -
Press prog before gate leaf
2 reaches the travel limit.
End calibration sensor 2
(closing direction)
Press prog before gate leaf
1 reaches the travel limit.
End calibration sensor 1
(closing direction)
The end of programming is
indicated by the courtesy
light switching on and the
display switching off.
NO
PROG
PROG
PRESS
PROG
PRESS
PROG
PRESS
PROG
PRESS
PROG
PRESS
PROG
DS1